Ordinary Maintenance; Routine Cleaning - Moretti Forni NordCap F100E Manual Del Usuario

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

available. Select the required program with the "SELECT" keys
and then press "+" e/o "-" to set the desired value.
-
"Eco delta below": indicates how many degrees less than the set
temperature the oven will reach in the Eco "stand-by" mode. Select
the required program with the "SELECT" keys and then press "+"
e/o "-" to set the desired value.
-
"Open valve": indicates the movement required for the steam valve
to be positioned in the open position in terms of percentage. Select
the required program with the "SELECT" keys and then press "+"
e/o "-" to set the desired value.
3.3.8
ALARMS DISPLAY/ SIGNALS
The appliance has an advanced self diagnostics system.
The following ALARMS can be displayed if there are any defects:
-
Max. safety temperature exceeded alarm: if the internal
temperature exceeds the maximum threshold, the safety thermostat
triggers automatically to block the operation of the oven; after
allowing it to cool down and making sure that none of the
components are damaged, unscrew the safety thermostat guard cap
(fig. 20pos. 3) and press down on the button underneath, which
resets the thermostat; restore the guard cap to its proper position to
prevent the thermostat from deteriorating, as this would prejudice
proper operation of the oven.
-
Thermocouple Failure Alarm:
thermocouple is damaged or disconnected. The display also
indicates which thermocouple is damaged.
-
Communication Error Alarm: indicates that communication
between the electronic boards is compromised. Ensure that the
cards are powered appropriately and connections are intact.
When one of the above alarms occurs the control unit indicates on screen
which alarm has been triggered, and turns the oven off. A similar screen
to Fig. 28 will be displayed characterized by a representative icon of the
error at the centre of the display (fig. 28 pos. A) below which there is a
text message
The acoustic and visual signal will remain until the "OK" key is pressed
and then the icon in the top bar will remain until the anomaly is solved.
In case of suspended anomaly, it is always possible to view the type by
opening the ALARMS item on the ASSISTANCE menu (see 3.3.7).
WARNING!
In case of malfunction or breakdown to the
appliance, press the "OK" button and perform the steps described in
3.7.
Leave the appliance to cool down and send for technical assistance to
remedy the cause of the failure and to make sure that no part of the
appliance is damaged.
The following SIGNALS may be displayed if there are any failures:
-
Steam Valve Malfunction: indicates a malfunction of the steam
valve or its movement/control system.
-
Electric panel over temperature: this indicates that the
temperature of the electric components compartment has exceeded
the threshold limit.
-
Abnormal shut down: displayed at start-up and indicates that the
oven was previously turned off incorrectly, and the provisions of
paragraph 3.7. were not followed.
WARNING!
the abnormal shut down signal must not be
taken into consideration ONLY in the following cases:
1. there is a real condition of danger so the oven is switched off
using the main button (fig. 15b part D).
2. there is a temporary and sudden interruption of
supply for external causes not caused by the user.
In all other cases follow the procedure to switch off the oven
appropriately, otherwise it will break down permanently
When there is a signal, the control unit shows the type of signal on the
screen. Press OK (fig. 28 pos. B) to acknowledge the visual and acoustic
signal (if any) and the message disappears. If necessary complete baking
and then contact Customer Care.
3.4
STARTING UP THE LEAVENING COMPARTMENT
WITHOUT HUMIDIFIER (F45E- F50E only)
The control panel is located on the front right-hand side of the
leavening compartment, as shown in figure 17.
1.
Indicator light (ON/OFF )
2.
Internal lighting on/off switch (light).
3.
On/off and regulation thermostat
To start the leavening compartment, proceed as follows:
a)
Switch on the leavening compartment by turning the thermostat
(fig.17 item 3); this will switch on the light (fig.17 item 1).
b)
Set the required temperature, up to a maximum of 65°C.
c)
To turn the leavening compartment off, turn the thermostat (fig.17
item 3) back to zero.
this indicates that the
electricity
UK/10
WARNING!
Do not touch the heating elements; there is a
risk of burning or scalding.
3.5
STARTING UP THE LEAVENING COMPARTMENT
WITH HUMIDIFIER
The control panel is located on the front right hand side of the
leavening compartment, as shown in figure 18.
1.
Humidifier ON/OFF switch.
2.
Compartment on/off light.
3.
Internal lighting on/off switch (light).
a) Fill the humidifier tray inside the leavening compartment with
water. The water must reach 2-3 cm above the level of the heating
element.
NOTE:
Remember to fill the humidifier tray so as to obtain
the necessary humidity, using demineralised water if possible.
b)
Switch on the leavening compartment by turning the thermostat
(fig.18 item 4); this will switch on the light (fig.18 item 2). c) Set
the required temperature, up to a maximum of 65°C.
d)
Press the switch (fig.18 item 1) to turn the humidifier heating
element on.
e)
Once the desired level of humidity has been obtained inside the
leavening compartment, turn the switch off (fig.18 item 1).
Should further humidity be required, turn the switch on again.
f)
To turn the leavening compartment heating elements off, turn the
thermostat (fig.18 item 4) back to zero.
WARNING!
Do not touch the heating elements; there is a
risk of burning or scalding.
3.6
STARTING UP THE EXTRACTOR HOOD
The hood is available with an extractor for cooking vapours.
The main switch of the extractor is located on the front right side of the
hood (fig.23 item C)
a)
Enable the switch to start the extraction.
b)
To switch off the extractor, move the switch to "O".
3.7
SHUT DOWN
F45E
- Switch off by moving the main switches of the oven (fig.15 item 1)
to "O", and also the switches of the leavening compartment (fig.17
items 2-3) (fig.18 item 1-3-4) and the hood extractor (fig.23 item C).
- Disconnect the power supply by turning off the main power switches
outside the equipment.
- Open the oven door.
- Turn off the stop cock.
F50E-F100E
To switch off the appliance, proceed as follows:
a)
hold down the STOP key for a few seconds. The display will show
the switching off screen. Wait until the oven cools down.
b)
switch off the main switches on the chamber (fig. 15b part. D), of
the leavening compartment (fig.17 parts 2-3) (fig.18 part. 1-3-4)
and the hood extractor (fig.23 part C).
WARNING!
The control unit must be switched off as
described in point a) so as not to cause irreversible damage.
- Disconnect the power supply by turning off the main power switches
outside the oven.
- Open the door of the oven.
- Turn off the stop cock.
When the oven is turned on again the display will be in the same state
as when it was last turned off.
4

ORDINARY MAINTENANCE

4.1
PRELIMINARY SAFETY OPERATIONS
WARNING!
Before
operation, disconnect the power supply by turning off the switches
fitted on the outside of the oven and/or the leavening compartment
and wait for the appliance to cool to room temperature. Always use
suitable protective equipment (gloves, eyewear...)
All precautions are decisive in ensuring that the oven remains in a
good state, and failure to observe them may result in serious
damage which will not be covered by the warranty.
4.2

ROUTINE CLEANING

After carrying out the operations described in point 4.1 above, clean
the appliance as follows:
Every day, at the end of operations and after leaving the appliance to
cool down, carefully remove from all parts of the oven any residues
performing
any
maintenance

Publicidad

Capítulos

Tabla de contenido
loading

Productos relacionados para Moretti Forni NordCap F100E

Este manual también es adecuado para:

493500600100

Tabla de contenido