Siemens SINAMICS G130 Manual De Listas página 1022

Rated motor temperature rise Calculated motor temperatures
Mot T_environment
p0625[M]
Mot T_on iron
Thermal
p0626[M]
3-mass-model
Mot T_on stator
(for induction motors
p0627[M]
only)
Mot T_on rotor
p0628[M]
Model tracking
Mot temp_sensor
p0600[M]
only
for
0
KTY
from encoder 1
1
[4704.8]
from encoder 2
2
[4704.8]
von Geber 3
3
[4704.8]
from Motor Modules 11
or CUA31
Mot Temperatur [°C]
p0603
10
[9576.7] (0)
e.g. r4105 from TM31
Mot temperatur [°C]
20
p0608[4]
(0)
e.g. r4105 from TM120
Mot temperatur [°C]
21
p0609[4]
(0)
e.g. r4105 from TM120
<1> For KTY and PTC, the value p0606 = 0 has a different meaning:
KTY: 0 The output of the timer is always switched out (logical 0)
PTC: 0 Delay time = 0 s
<2> As for the switch-in delay, refer to [1024]. p0607 = 0 suppresses fault F07016.
<3> For KTY and "No sensor", temperature as defined in the model.
<4> Applies only for VECTOR.
<5> P0606 does not work for alarms via p0616.
<6> p0601 = 5 can only be evaluated if r0192.15 = 1 and p0600 = 11; PT100 is calibrated via p0624.
<7> The assignment of temperature channels 1 ... 4 depends on the hardware used.
<8> The relevant rated response temperature (°C) depends on the temperature sensor chosen by the motor manufacturer.
1 2
DO: SERVO, VECTOR
Signals and monitoring functions - Thermal monitoring, motor
MotTMod T_environ
r0630[M]
MotTMod T_iron
MAX
r0631[M]
MotTMod T_copper
r0632[M]
MotTMod T_rotor
r0633[M] 1
<7>
Mot temp_sensortyp
p0601[M]
Mot Temp_sensortyp
r4620[0] r4620[1] r4620[2]
Mot temp_sensortyp
0 = No sensor
Temperature channel
1 = PTC alarm and
1 2 3
time p4600[E] p4601[E] p4602[E]
2 = KTY84
Mot Temp_sensortyp
r4620[0] r4620[1] r4620[2]
Configuration
3 = KTY84 & PTC,
Mot temp_sensortyp
for encoder only
0 = No sensor
10 = PTC fault
Temperature channel
4 = Bimetal NC
contact alarm 11 = PTC alarm
1 2
with time step
p4610[M] p4611[M] p4612[M] 12 = PTC alarm and time step
for MM only
20 = KTY84
Configuration
5 = PT100 <6> 30 = Bimetal NC contact fault
0 = No sensor
31 = Bimetal NC contact alarm
10 = Evaluation of
32 = Bimetal NC contact 10 = PTC fault
several
alarm & time step
temperature
11 = PTC alarm
channels
12 = PTC alarm and time step
SME12x)
20 = KTY84
11 = Evaluation of
30 = Bimetal NC contact fault
several
temperature
31 = Bimetal NC contact alarm
channels (BICO)
32 = Bimetal NC contact
alarm & time step
3 4
Mot_temp
1
r0035
Mot_temp fault thresh
p0605[M]
1
0
r4620[3]
KTY sensor type
(threshold not applicable for PTC)
4
Mot_tempAlrmThresh
p4603[E]
p0604[M]
Mot temp alarm 1
r4620[3]
p0616[M]
M I N
3 4
p4613[M]
1650
<8>
KTY PTC
Sensor type
<3>
Mot temp_sens time
-140 °C 250 °C
5
fp_8016_54_eng.vsd
07.10.09 V04.03.01
p0610[M]
p0610 = 0: No response, only alarm, no reduction of I_max
p0610 = 1: Alarm and reduction of I_max and fault
p0610 = 2: Alarm and fault, no reduction of I_max
<4>
&
Fault response
p0610 = 1
Suppress fault
I_max reduction
&
[1690.1][6640.2]
p0606[M]
<1> <5>
T 0
F07011
&
"Motor overtemperature"
1
1
r2135.12
[8017.8]
1
A07910
"Motor overtemperature"
0
p0607[M]
1
r2135.14
<2>
A07016
T 0
"Motor temperature
sensor fault, fault"
A07015
"Motor temperature
sensor fault alarm"
A07820 "Temperature sensor not connected"
6 7
Function diagram
S120/S150/G130/G150
1.00 s
p0610 = 0
[2548.2]
[2548.2]
8
- 8016 -