Kärcher B 260 RI R100 Manual Del Usuario página 22

12. Close the stop valve at the back of the waste water
tank.
13. Select "Tank rinsing" on the display.
Emptying the waste container
Note
The waste container can only be removed via the driv-
er's side and is only present on R cleaning heads.
1. Pull the tab.
2. Pivot open the squeegee blade holder.
3. Remove the waste container.
Illustration AI
Tab
1
Squeegee blade holder
2
Waste container
3
4. Empty the waste containers.
5. Fit the waste container.
Note
The waste container must latch into place.
6. Pivot the squeegee blade holder closed.
Draining fresh water
ATTENTION
Cleaning solution in the fresh water tank
Damage to fresh water tank, valves and seals
Never leave the cleaning solution in the fresh water tank
at the end of operation.
1. Remove the fresh water drain hose from the holder
and lower it over a suitable collecting device.
2. Drain the cleaning solution.
3. Remove the fresh water tank cap.
4. Rinse the fresh water tank with clear water (maxi-
mum 60 °C).
Shutting down the device
1. Turn the key-operated switch to "OFF".
2. Remove the Intelligent Key.
3. Secure the device against rolling away.
4. Charge the battery if necessary.
Grey Intelligent Key
The grey Intelligent Key grants the supervisory staff ex-
tended authorizations and setting options.
1. Insert the Intelligent Key.
2. Select the desired function by turning the info but-
ton.
Transport journey
1. Set the program selector switch to "Transport trav-
el".
2. Press the Info button.
The following settings can be made in the Transport
travel menu:
● Resetting the maintenance counter
● Resetting the day counter
● Key management
● Choosing the brush shape
● After-running time
● Standard setting
● Setting the language
● Switch menu
● Travel speed
● Factory setting
● Activating the manual tank rinsing gun
Resetting the maintenance counter
If maintenance work shown in the display has been car-
ried out, the corresponding maintenance counter must
then be reset.
1. Turn the Info button until "Maintenance Cntr" is dis-
played.
2. Press the Info button.
The counter readings are displayed.
3. Turn the info button until the counter to be cleared is
highlighted.
4. Press the Info button.
5. Select "Yes" by turning the Info button.
6. Press the Info button.
The counter is cleared.
Note
The service counter can only be reset by Customer Ser-
vice staff.
The service counter shows the time until the next ser-
vice due by Customer Service.
Resetting the counter
1. Turn the Info button until "Counter" is displayed.
This menu shows the total operating hours and the
day counter.
Delete the day counter:
2. Press the Info button.
The "Delete counter" menu is displayed.
3. Turn the Info button until "Day counter" is highlight-
ed.
22
4. Press the Info button.
Key management
The authorizations are assigned for each yellow Intelli-
gent Key used and the language of the display is set for
this Intelligent Key in the "Key Manager" menu item.
1. Insert the grey Intelligent Key.
2. Turn the info button until the "Key Manager" menu
item appears on the display.
3. Press the Info button.
4. Remove the grey Intelligent Key and insert the yel-
low Intelligent Key to be personalized.
5. Select the menu item to be changed by turning the
info button.
6. Press the Info button.
7. Select the setting of the menu item by turning the in-
fo button.
8. Confirm the setting by pressing the menu item.
9. Select the next menu item to be changed by turning
the info button.
10. After all settings have been made, call up the
"Save?" menu by turning the info button.
11. Press the Info button.
The authorizations are saved.
The "Key Manager continue?" display appears.
● Yes: Program another Intelligent Key
● No: Exit the key menu
12. Press the Info button.
Choosing the brush shape
This function is required when changing the cleaning
head.
1. Turn the info button until the "Brush Head" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired brush shape is
highlighted.
4. Press the Info button.
5. To change the cleaning head, move the lifting drive
by turning the info button:
 "up": Lifting
 "down": Lowering
 "OFF": Stopping
6. Turn the info button until the "OFF" menu item is dis-
played.
7. Press the Info button.
The menu is exited.
The controller performs a restart.
After-running time
1. Turn the info button until the "After-Run Time" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired function is high-
lighted.
4. Press the Info button.
5. Turn the info button until the desired after-running
time is displayed.
6. Press the Info button.
Standard setting
1. Turn the info button until the "Basic Settings" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired accessory is
highlighted.
4. Press the info button to confirm ON/OFF.
5. Press the info button to exit the menu.
6. Switch the device off and on again to adopt the set-
ting.
Setting the language
1. Turn the info button until the "Language" menu item
appears on the display.
2. Press the Info button.
3. Turn the info button until the desired language is
highlighted.
4. Press the Info button.
Switch menu
The following functions are switched on and off via the
"Switch Menu":
● Detergent dosing*
● Flashing beacon/ spotlight*
● Side brush spray nozzles*
● Spray suction
● Work lights
● Tank rinsing
The "Switch Menu" is available in all program switch po-
sitions, except "OFF".
1. Press the Info button.
The "Switch Menu" is displayed.
2. Press the Info button.
The list of functions available in the device is dis-
played.
3. Turn the info button until the desired function is high-
lighted.
4. Press the info button to change the switch state.
English
5. Turn the Info button until "Quit Menu?" is displayed.
6. Press the Info button.
* Optional
Adjusting the travel speed
1. Turn the info button until the "Travel speed" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired maximum
speed is highlighted.
4. Press the Info button.
Factory setting
The factory settings of all parameters are restored (ex-
cept transport travel speed).
1. Turn the info button until the "Factory Settings"
menu item is displayed.
2. Press the Info button.
3. Turn the Info button until "Yes" is highlighted.
4. Press the Info button.
Adjusting parameters for cleaning programs
All cleaning program parameters are retained until an-
other setting is selected or the device is switched off.
1. Set the program switch to the desired cleaning pro-
gram.
2. Press the Info button.
The first adjustable parameter is displayed.
3. Press the Info button
The adjusted value flashes.
4. Set the desired value by turning the Info button.
5. Confirm the changed setting by pressing the Info
button or wait until the set value is automatically ac-
cepted after 10 seconds.
6. Select the next parameter by turning the Info button.
7. After changing all desired parameters, turn the Info
button until the "Quit Menu?" menu item is dis-
played.
8. Press the Info button.
The menu is exited.
Standard setting
Parameter changes made in the individual cleaning pro-
grams during operation are reset to the standard setting
when the device is switched off.
1. Turn the info button until the "Basic Settings" menu
item appears on the display.
2. Press the Info button.
3. Turn the info button until the desired cleaning pro-
gram is highlighted.
4. Press the Info button.
5. Turn the Info button until the desired parameter is
highlighted.
6. Press the Info button.
The adjusted value flashes.
7. Set the desired value by turning the Info button.
8. Press the Info button.
White intelligent key
Inserting the white Intelligent Key unlocks the device
and enables it for the use with preset parameters.
White Intelligent Keys can be used so that an Intelligent
Key with adapted parameters can be created for each
cleaning task.
The operator cannot change the parameters and they
are independent of the selection of the cleaning pro-
gramme on the program selection switch (the functions
"0", transport, vacuuming remain unchanged).
The grey Intelligent Key can be used to set the following
parameters for the white Intelligent Key:
● Travel speed
● Working speed
● Brush speed (only with R cleaning head)
● Contact pressure
● Water quantity
● RM dosing
● Suction system
● Work light
● Flashing beacon
● Detergent dosing unit ON/OFF
● Pre-sweeping unit
● Suction bar water valve
● Language
Programming the white Intelligent Key
1. Insert the grey Intelligent Key.
2. Turn the info button until the "Key Manager" menu
item appears on the display.
3. Press the Info button.
4. Remove the grey Intelligent Key and insert the white
Intelligent Key to be personalized.
5. Select the menu item to be changed by turning the
info button.
6. Press the Info button.
7. Select the setting of the menu item by turning the in-
fo button.
8. Confirm the setting by pressing the menu item.