Publicidad
Idiomas disponibles
Idiomas disponibles
IMPORTANT! KEEP THESE INSTRUCTIONS FOR
EN
FUTURE REFERENCE.
SAFETY REQUIREMENTS AND PROPER USE OF THE PRODUCT
WARNING!
• Please read the manual carefully before using this product and keep it for future reference.
• DO NOT USE THE WARMER WHEN THERE IS NO WATER INSIDE!
• The appliance is intended to be used in household and similar applications such as staff kitchen areas in shops, offices and other working environments; farm houses; by clients in
hotels, motels and other residential type environments; bed and breakfast type environments.
• Before first use, remove the packing and remove everything from inside.
• Do not reach for the device if it fell into the water, immediately disconnect it from the power supply.
• When cleaning the unit must be disconnected from power supply.
• Children and persons with reduced physical or mental efficiency can use the device under the control of the people that will guarantee their safety.
• Adult use only. Keep away from children. The device and its wire must be kept out of the reach of children under 8 years of age. The device is not a toy.
• Cleaning and user maintenance shall not be made by children.
• Do not use the device for purposes other than those for which it is intended.
• Before connecting the plug into an electrical socket, make sure that the voltage shown on the rating plate corresponds to the mains voltage in socket. If the voltages do not match, do
not connect the device.
• Never use accessories that have not been supplied with the device and are not recommended by the manufacturer.
• Unplug the device by holding the plug, do not pull on the electric wire.
• Do not use the device if the power cord or plug is damaged, exchange or repair should be entrusted to a specialized service. Individual interventions in the device during the warranty
period will cause loss of this warranty.
• Do not store or place the device, its accessories and cord near hot surfaces.
• Do not let the power cord get in touch with hot parts of the device.
• Do not let the main cord hang over the edge of the table or worktop on which the appliance stands.
• This appliance is intended for household use only, do not use it in an industrial environment or outside.
• Keep in a dry, cool place (0-40° C), avoid exposure to sunlight.
• Use the unit on a clean, non-greasy, dry surface.
• Do not place the working devise on metal surfaces and window sills.
• Never immerse in water or any other liquid the main body of the device, especially when the device is connected to an electric network.
• Fill the water tank with cold water only.
• The manufacturer takes no responsibility for damages caused by incorrect use of the product and its accessories.
• After use, leave the device to cool down.
• The device heats to a high temperature. Extreme care is needed during the operation.
• The device cannot be left unattended during operating.
• Do not touch the working devise with wet hands.
• Do not allow children to play with packaging parts (such as plastic bags, card-boards, polystyrene). Danger of suffocation.
• Water in the appliance heats up to high temperatures. Take particular caution when mixing food or taking the container out of water-bath.
• Always check food temperature before feeding.
• Before feeding, please drop a few milk drops on your hand to check the temperature. Pay attention to the food heating time should not be too long, as it could damage food nutrition.
• The appliance should be used for milk and food warming, sterilization of baby accessories, defrosting frozen milk (kept in storage milk bags or containers) and maintaining the
temperature of a liquid or soft food.
• The appliance can be used for heating up and keeping food warm in standard baby food jars and bottles.
• Do not pour milk and food directly into the device for heating or defrosting.
• You should not heat up food and milk for too long. Food and milk should be served immediately when heated up because food and milk at 25°C 42°C are particularly favourable for
the growth of bacteria and germs. For the same reason you should not use food and milk remains.
• Prior to heating up food from baby food jars or bottles, you should remove labels, tags, prices and other paper stickers which may come off during heating and clog the appliance
inner surfaces or stick to the heating plate. You should also take off a lid from a baby food jar.
• In order to heat up food evenly you should periodically mix it taking caution all the time.
• In order to reduce the formation of lime-scale it is recommended to use boiled or filtered water.
• Water should always be poured into prior to connecting the appliance to the power supply.
• The amount of water in the appliance depends upon the size of your container. Please make sure that water does not exceed the Max level, spill and pour onto the appliance. If so,
wipe the appliance dry prior to its connection.
• Please unplug the power supply if it is not used for a long time.
• When the product is used in the early stage, slight plastic smell is easy to appear after high temperature, which is a normal phenomenon.
PARTS (FIGURE I):
1. Transparent cover; 2. Basket; 3. Main body/main device; 4. Control panel.
DIRECTION FOR USE:
The warmer is intended for easy and safely milk and food warming, defrosting and sterilization. Jars and bottles which are warmed up to high temperatures or which are sterilized
should withstand heating up to minimum 100°C. The function Sterilization by 100°C is intended for bottles and accessories for which the manufacturer has indicated that they may be
sterilized by means of boiling. Breast milk storage bags always should be in intact condition when you place them in the warmer.
The warmer can hold one feeding bottle or jar with a diameter under 7.5 cm. The water gets warm thanks to a heating plate, which is mounted on the bottom of the appliance and
on this way it defrosts and warms up the bottle/food container and its content. The time of warming or defrosting depends on: the food type, on the quantity of the food/liquid, on its
initial temperature, on the temperature of the poured water, on the material used for the processing of the bottle/food container.
DISPLAY (FIGURE II):
1. LED display – time and temperature; 2. Increase button; 3. Sterilization; 4. Food warming; 5. Power button ON/OFF; 6. Fast milk warming; 7. Defrosting; 8. Keep warm function; 9.
Decrease button.
INSTRUCTION FOR USE:
Caution! Do not use the warmer when there is no water inside!
ASSEMBLY:
1. For a better user experience and later maintenance, please use a wet tissue to wipe the inside and outside of the machine prior to use. Please clean the baby bottle basket and cover
with warm water and a dishwashing liquid. Rinse thoroughly and gently dry.
2. Place the basket inside the main unit (Figure I);
3. Before first use, pour around 100ml clean water into the appliance. Select the sterilization function to work and disconnect the product after 10 minutes of work. By doing so you can
check whether the device is in good condition or not. After the operation, pour out the internal water of the appliance and let it dry. Next time you can use it normally.
OPERATION:
Fast milk warming function ((Figure II, III A, IV)):
ENGLISH
IMPORTANT! KEEP THESE INSTRUCTIONS FOR
EN
FUTURE REFERENCE.
• Follow the step 1 and 2 from the section Assembly.
• Pour only 40ml distilled water into the bottle warmer.
• Put the feeding bottle into the appliance. (Do not put the transparent cover above. You do not need it).
• Make ensure no water is spilled.
• Connect the power cord to the appropriate electrical outlet. The information is located on the rating label, on the bottom of the device.
• The buzzer will beep once, when plugged in. Touch the power button (Figure II, 5) to turn on the device.
• Touch once the fast warming button (Figure II, 6) to select the mode. The screen shows default temperature 37°C and heating time 3 minutes. Use the increase and decrease buttons
(Figure II, 2, 9) to adjust the time. Please, for time setting refer to the reference chart in IV – 1. Bottle type; 2. Glass; 3. Plastic; 4. Milk initial temperature; 5. Water volume; 6. Milk
volume.
• This function is used when you need to warm milk quickly. The principle of this function is to heat up water fast. The temperature of water inside the compartment will increase over
50°C (after 5 minutes) or over 70°C (after 10 minutes). The milk in the bottle can not reach such a high temperature in short time. Hence, the milk will be heated up to the required
temperature more quickly. Please, do not keep the feeding bottle for a long time in this function, because the milk could be overheated and lose its nutrients.
• The bottle warmer will start working after the time indicator flashes twice. The indicator light keeps flashing and the timer indicator is counting down while this function is working.
• When the time countdown is over, the bottle warmer will beep 5 times then, it will automatically switch to the keep warm mode, the default setting is 24 hours.
• The temperature of the fast warm function is not adjustable. This setting helps to warm milk to 37°C by steam.
• The adjustable range of time is 1-10 minutes.
• The speed of warming milk depends on the milk volume, its initial temperature, i.e. room temperature or fridge temperature. When you find the milk is not warm enough, you can
place the bottle back into the appliance for a maximum of 0.5-1 minutes of extra warming. This will create a slightly warmer result but without overheating.
• If you leave the bottle in the bottle warmer longer than the time indicated in the setting table, the milk may become overheated.
• If water dries out, the product will shut down due to high temperature detected (you can not turn on the bottle warmer by pressing the power button at this time). Wait 10 minutes
add 40 ml of room temperature water into the chamber and wait for 3 minutes to cool down the milk warmer, then press the power button to restart.
Caution:
The water in the bottle warmer might be hot after finishing warming milk/baby food. Be careful that hot water can cause serious burns.
FOOD WARM FUNCTION (FIGURE II, III B):
• Follow the step 1 and 2 from the section Assembly.
• Pour not more than 160ml distilled water into the bottle warmer. We recommend the water level and food level to be the same.
• Put the food jar into the appliance. (Do not put the transparent cover above. You do not need it).
• Make ensure no water is spilled.
• Connect the power cord to the appropriate electrical outlet. The information is located on the rating label, on the bottom of the device.
• The buzzer will beep once, when plugged in. At standby mode, press the food warming button (Figure II, 4), the indicator light of the icon will start flashing. Screen will show default
temperature 70°C flashing and default heating time 6 hours.
• You can adjust the temperature while it is flashing by pressing the increase and decrease buttons. If you want to adjust the time, press the button again, the timer indicator will start
flashing and you can adjust it as desired.
• The bottle warmer will start working after the temperature/time indicator flashes twice. The food warming indicator light will keep flashing and the timer indicator will count down
while this function is working.
• When the time countdown is over, the bottle warmer will beep 5 times to remind you to check whether your food is ready.
Notes:
• The adjustable range of temperature is 50-80°C
• The adjustable range of time is 2-59 minutes, 2-24 hours.
• Press the food warming button again to switch between temperature/time.
• The temperature indicator light always shows the real time water temperature while the product is working.
Caution:
Make sure to stir the baby food during warming as it does not circulate automatically. Before feeding, always stir the food well and check its temperature to make sure the food is
heated evenly.
STERILIZE FUNCTION (FIGURE II, III C):
• Follow the step 1 and 2 from the section Assembly.
• Pour around 100-150ml distilled water into the bottle warmer.
• Put the disassembled feeding bottle and its accessories into the appliance. Make sure the bottle mouth is facing down and no water is spilled. Put the transparent cover above.
• Connect the power cord to the appropriate electrical outlet. The information is located on the rating label, on the bottom of the device.
• The buzzer will beep once, when plugged in. At standby mode, press the sterilization button (Figure II, 3), the indicator light of the icon will start flashing. The screen will show
default temperature 100°C flashing and default heating time 10 minutes flashing.
• You can adjust the time while it is flashing by pressing the increase and decrease buttons.
• The sterilization starts after the time indicator flashes twice. The indicator light keeps flashing and the timer indicator is counting down while this function is working.
• After the countdown is over, the bottle warmer will beep 5 times and enter the standby mode.
• Be careful not to get burned when taking out the bottle after disinfection
Notes:
• The temperature of the sterilize function is not adjustable, and the temperature indicator light always shows the actual water temperature while the product is working.
• The adjustable range of time is 5-20 minutes.
• The water volume cannot exceed the maximum scale line.
• If water dries out, the product will shut down due to high temperature detection (you can not turn on the bottle warmer by pressing the power button at this time). Wait 10 minutes
or add 40ml of room temperature water into the chamber and wait for 3 minutes to cool down the milk warmer, then press the power button to restart.
DEFROST FUNCTION (FIGURE II, III D):
• Follow the step 1 and 2 from the section Assembly.
• Pour not more than 160ml distilled water into the bottle warmer. We recommend the water level and food level to be the same.
• Put the bottle/container into the appliance. (Do not put the transparent cover above. You do not need it).
• Make ensure no water is spilled.
• Connect the power cord to the appropriate electrical outlet. The information is located on the rating label, on the bottom of the device.
• The buzzer will beep once, when plugged in. At standby mode, press the defrosting button (Figure II, 7), the indicator light of the icon will start flashing. The screen will show default
temperature 37°C flashing and default heating time 24 hour.
• You can adjust the temperature while it is flashing by pressing and the increase and decrease buttons. If you want to adjust the time, press the defrosting button again, the timer
indicator will start flashing and you can adjust it as desired.
• The bottle warmer will start working after the temperature/time indicator flashes twice. The defrosting indicator light will keep flashing and timer indicator will count down while
this function is working.
• When the time countdown is over, the bottle warmer will beep 5 times to remind you to check whether your food is ready.
Notes:
• The adjustable range of temperature is 32-42°C.
• The adjustable range of time is 2-59 minutes, 2-24 hours.
• Press defrosting button again to switch between temperature/time.
ENGLISH
Publicidad
