Sub-Zero ICB424 Instrucciones De Instalación página 8

Models ICB424 and ICB424FS Installation
Kickplate Installation
Once the unit is leveled and wiring connections made, the
kickplate can be installed. Use the two #10 x 13 mm stain-
less steel screws that are provided with the kickplate.
Refer to the illustration below.
IMPORTANT NOTE: The kickplate must be removed for
servicing. The floor cannot interfere with removal. The
louvered section of the kickplate must not be covered so
as to prevent air circulation.
Turn power back on to the electrical outlet.
KICKPLATE
Kickplate installation.
Door Panel—Model ICB424
Model ICB424 is offered in two design applications; stain-
less steel (/S) and overlay (/O). Each of these designs are
available as a glass door (G) model.
The stainless steel model ICB424/S is available as a glass
door (G) model only, with the classic finish and is shipped
from the factory with the decorative stainless steel door
panel and matching handle in place.
The overlay model ICB424/O is available as a glass door
(G) or solid door (S) model and is designed to accept a
decorative door panel to match surrounding cabinetry.
The door panel and the handle will be provided by the
customer.
Before beginning installation, check for the correct com-
ponents for the fit and finish desired. All overlay doors
require a decorative panel 603 mm by 764 mm and a
minimum 16 mm thick.
If you have questions, contact your Sub-Zero dealer or
cabinet supplier. Additional panel information can be
found in the Sub-Zero design guide.
A solid panel must not be installed on a glass door
unit, as this may cause moisture to form behind the
panel.
Overlay Door Panel—Model ICB424
Inspect the door panel for the minimum 16 mm thickness,
the finished inside edge. The glass door has a 5 kg weight
limit and the solid door has a 9 kg weight limit. Refer to
the wine storage section of the Sub-Zero design guide for
additional panel information.
Decide if the handle will be attached through the glass
door frame or just through the decorative door panel. If it
is just through the door panel, the handle must be
attached first.
Decorative panels are attached to the model ICB424 door
using #8 x 16 mm square drive screws passing through
the door frame from the rear, behind the gasket into the
panel. The door panel is marked for screw locations by the
use of 'tenon centers', which are temporarily inserted into
the 6 mm diameter holes in the front of the glass door
frame. Refer to the illustration below.
With the wine storage unit secured in position and the
door closed, the panel is held in the desired position on
the door and rapped by hand from the front, putting center
marks on the rear surface of the panel. If the door panel is
made of such a material that pre-drilling is needed, all of
the mounting holes should be marked. If not, only enough
holes to hold the panel in place temporarily, are necessary.
GASKET
OVERLAY
PANEL
DOOR
FRAME
DIAMETER
TENON CENTER
Overlay panel. Door frame cross section.
The door panel is then lowered from the door frame, tenon
centers removed, the door opened and the screws driven
into the panel through the black tape on the door frame,
using the center marks to locate the screws.
The screw holes inside the door are hidden under a cover
flap on the door gasket. It is necessary to lift the flap to
insert the screws. Use as many screws as necessary to
hold the door panel in place properly.
IMPORTANT NOTE: After the first three or four mounting
screws are in place, but not completely tightened, close
the door and check your panel fit. This is the time to make
small adjustments. Once you are satisfied with the appear-
ance, open the door and apply the remainder of the
screws. Check all screws for tightness.
The metal frame on the glass door has numerous
mounting holes on each side of the door. This is to accom-
modate the Sub-Zero accessory handles and provide for
easy attachment of the handle through the door frame.
If you choose not to use the pre-drilled handle mounting
holes, it will be necessary to fasten the handle from the
rear of the door panel only, or drill one or more additional
holes through the metal frame of the glass door.
The cross section illustration shows how this hole passes
through the door frame. The hole center is on the small
locator groove in the front of the frame. A 6 mm diameter
hole is made in the front wall of the extrusion and a 11 mm
diameter hole through the rest of the frame.
11 mm
DIAMETER
GLASS
6 mm
8