Descargar Imprimir esta página

Moretti Forni R Serie Manual Instrucciones página 17

Ocultar thumbs Ver también para R Serie:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

Proceed by inserting the vapour exhaust pipe into the suction device
connector (Fig. 7 item A).
NOTE: connect the vapour exhaust to the outside using a pipe
with minimum diameter 150 mm.
Any extensions must be fitted so that the top pipes slot into the
bottom ones.
Install the suction device cover housing (Fig. 7 item D).
2.5.2 ELECTRICAL CONNECTION
WARNING! Electrical connection must only be carried out by
specialised personnel, in compliance with current local state
Electric Quality Assurance Corporation requirements.
- Before starting the connection procedure, check that the
earthing system is provided in accordance with European EN
standards.
- Before starting the connection procedure, check that the main
power switch has been turned to the "off" position.
- The rating plate contains all the information necessary for
proper connection.
- Fit a main four-pole switch with fuses or an automatic switch
suitable for the values shown on the plate, to allow the appliance
to be disconnected from the mains.
NOTE!: the device selected should be in the immediate vicinity of
the oven and within easy access.
- The oven is delivered with the required voltage indicated on the
rating plate (See Fig. 2).
- To carry out electrical connection, remove the protective cover
located on the rear side of the appliance.
The connection cable must be supplied by the installer.
When connecting to the power mains, it is necessary to fit a plug that
complies with the standards and regulations in force.
- Insert a cable of the correct section (See Tab.1) into the cable
raceway provided (Fig. 8 item H) and then connect it to the terminal
board as illustrated (Fig. 8 item E or F).
- When connection has been completed, check that the supply
voltage, with the appliance running, does not differ from the rated
value by more than ± 10%.
WARNING! The flexible wire for connection to the power supply
must have characteristics at least equal to the model with rubber
insulation H07RN-F and must have a rated section suited to the
maximum absorption (See Tab.1).
WARNING! It is essential that the oven be properly earthed. A
special terminal is provided for this purpose on the connection
terminal board (Fig. 8 item E or F). It is marked with the earth
symbol and the earth wire must be connected to it.
When connections have been completed, check that the carriage
rotates in a clockwise direction (seen from above) and that the
vapour suction fan turns in the right direction.
WARNING! When disconnecting from the power mains, after
switching off the appliance, wait at least 15 MINUTES before
unplugging it in order to allow the electronic circuits inlet
condensers to discharge. Never touch the plug contacts under
any circumstances.
WARNING!: The manufacturer declines any responsibility in
the event of failure to comply with the above safety precautions.
2.5.3 CONNECTING TO THE WATER SUPPLY
Connection to the water supply must be made in accordance with
current regulations in force in the country of installation and flexible
pipes for the connection to the water supply network must comply
with IEC 61770 and subsequent modifications.
WARNING! A tap must be fitted upstream of the appliance to
shut off the water supply.
The 3/4 male gas type water filler is located at the rear of the oven
(Fig. 8 item G). The working pressure must be between 1 and 1,5
bar.
WARNING! Higher pressures may result in situations that are
dangerous for persons and harmful for the appliance.
The appliance must be connected to a supply of soft water.
For preference, a flexible pipe should be used so as to avoid even
small pressure changes in the water supply.
Leave the water to run through the pipe before connecting the oven.
If the oven is connected to a supply of hard water this will cause
rapid calcification of the pipes.
NOTE!: The manufacturer declines any responsibility in the
event of failure to comply with the above safety precautions.
2.5.4 CONDENSATION DRAINAGE CONNECTION
A 15mm connector is also provided on the rear of the appliance to
drain condensation (Fig. 8 item I).
Connect a rubber pipe to the connector.
3
OPERATION
3.1
PRELIMINARY CONTROL OPERATIONS
WARNING! Before commencing start-up and programming of
the oven, always check that:
- all electrical and earthing connections have been properly
made.
- all vapour exhaust connections have been properly made.
All control operations must be carried out by specialised
technicians holding a valid license.
Before using the oven, clean it as described in point 4.2.
WARNING! Before starting up the appliance each time:
- Check that the warning signs on the oven (fig.3) are undamaged
and easily legible. If this is not the case, replace them. Locks
must be present and working properly.
- Any damaged or missing components must be replaced and
properly fitted before the appliance is used.
WARNING!:
- The oven must always be under surveillance when in operation.
- During operation the oven surfaces, and in particular the glass,
become hot, so that care must be taken not to touch them so as to
prevent scalding.
- When opening the door make sure you stand at a safe distance
from any hot steam that may come out of the baking chamber.
- Never allow unauthorised persons to approach the oven.
- There is a safety handle on the inside of the door, to be used in
case of accidental closure of the door with somebody inside the
baking chamber. To open the door from the inside, turn the
safety handle clockwise.
Do not overload the trays with items and always abide by the
minimum space required between the items and the tray above.
Before placing items inside the oven, it is advisable to set the oven to
a temperature above the envisaged set point for cooking and then to
lower the temperature to the required setting.
For more even results, we recommend avoiding the use of
temperatures above those recommended for the type of product being
baked.
3.2
STARTING UP THE OVEN
The control panel is fitted on the front right hand side of the baking
chamber, as illustrated (Fig.10).
The oven is turned on by setting the main switch (fig.2 item 2) to
position "1" and then pressing the On/Off button (Fig. 10 item 1).
3.2.1 SETTING THE LANGUAGE:
To set the language (Italian, English, French, German and Spanish),
press the right arrow and up arrow keys simultaneously (fig. 10 item
9 and 8), then select the language using the up and down arrow keys;
press OK to confirm.
The control unit can be set to show the temperature in degrees
Centigrade or in degrees Fahrenheit, to change the setting see point
5.12, to adjust the contrast on the screen see point 5.13.
3.2.2 THE KEYBOARD (fig. 10 )
The following keys are located close to the monitor, and details of
their uses will be given later in the manual:
1) main On/Off button
2) LCD display
3) OK button
4) Start/Stop button
5) Steam button
6) Light button (oven light).
7) left arrow
8) up arrow
9) right arrow
10) down arrow
Scroll through and select the various parameters using the left and
right arrow keys. The up arrow and down arrow keys are used to
modify the value to be set.
UK3

Publicidad

loading

Este manual también es adecuado para:

R14e