Publicidad
Idiomas disponibles
Idiomas disponibles
EN USER
1A GENERAL WARNINGS AND SAFETY
The instruction manual is an integral part of the product and it must
therefore be kept carefully and must accompany the appliance; if the
manual is lost or damaged, another copy must be requested from the
Technical Assistance Centre.
Boiler installation and any other assistance and maintenance op-
eration must be carried out by qualified personnel according to
the indications of current local regulations.
For installation, it is advisable to contact specialised personnel.
The boiler must only be used for the application foreseen by the
manufacturer. The manufacturer shall not be liable for any dam-
age to persons, animals or property due to errors in installation,
calibration, maintenance or due to improper use.
The safety and automatic adjustment devices must not be modi-
fied, during the system life cycle, by the manufacturer or supplier.
This appliance produces hot water, therefore it must be connect-
ed to a heating system and/or a domestic hot water mains, com-
patible with its performance and output.
In case of water leakage, close the water supply and contact the
Technical Assistance Service immediately.
In case of absence for long periods time, close the gas supply
and switch off the electrical supply main switch. If there is a risk
of frost, drain the boiler.
From time to time check that the operating pressure of the hy-
draulic system does not decrease under 1 bar.
In case of failure and/or malfunctioning, deactivate the appli-
ance, and do not try to repair or intervene directly on it.
Appliance maintenance must be carried out at least once a year:
scheduling it with the Technical Assistance Service will avoid
wasting time and money.
At the end of its life, the product should be not be disposed of
as solid urban waste, but rather it should be handed over to a
differentiated waste collection centre.
Boiler use requires strict observation of some basic safety rules:
Do not use the appliance in any manner other than its intended
purpose.
It is dangerous to touch the appliance with wet or damp body
parts and/or in bare feet.
Under no circumstances should you cover the intake grids, dis-
sipation grids and ventilation vents in the installation room with
cloths, paper or any other material.
Do not activate electrical switches, telephone or any other object
that causes sparks if there is a smell of gas. Ventilate the room
by opening doors and windows and close the gas central tap.
Do not lean any object on the boiler.
Do not perform any cleaning operation until the appliance has
been disconnected from the main power supply.
Do not access the inside of the boiler. Any work on the boiler
should be carried out by the Technical Assistance Centre or by
professionally qualified personnel.
Do not access the inside of the boiler. Any work on the boiler
should be carried out by the Technical Assistance Centre or by
professionally qualified personnel.
Do not cover or reduce ventilation opening of the room where the
generator is installed.
Do not leave containers and inflammable products in the installa-
tion room.
Do not attempt to repair the appliance in case of failure and/or
malfunctioning.
It is dangerous to pull or twist the electric cables.
it is forbidden to intervene on sealed elements.
This appliance should not be operated by children younger
than 8 years, people with reduced physical, sensory or men-
tal capacities, or inexperienced people who are not familiar
with the product, unless they are given close supervision or
instructions on how to use it safely and are made aware by a
responsible person of the dangers its use might entail. Children
must not play with the appliance. It is the user's responsibility to
clean and maintain the appliance. Children should never clean
or maintain it unless they are given supervision.
It is forbidden to obstruct the condensate outlet.
For better use, remember that:
- regular external cleaning with soapy water not only improves the
appearance but also protects panelling against corrosion, extending
its life cycle;
- if the wall-hung boiler is enclosed in wall-mounted cabinets, leave at
least 5cm for ventilation and maintenance;
- the installation of an ambient thermostat will ensure greater comfort,
more rational heat use, and energy savings; the boiler can also be
connected to a programming clock in order to manage ignition and
switch-off during the day or week.
2A APPLIANCE IGNITION
At the same time, if it is necessary to put the appliance in service again,
carefully follow the described operations.
To start-up the boiler it is necessary to carry out the following opera-
tions:
- power the boiler
- open the gas tap present in the system to allow fuel flow
- set the ambient thermostat at the required temperature (~20°C)
- turn the function selector (3 - fig. 3) to the required position:
Winter: turn the function selector (3 - fi g. 3) in the area marked with
+ and - (fi g. 24b) to obtain DHW and heating. In the case of a heat
request, the boiler will switch on and the digital display will show the
temperature of the heating water, the heating mode icon and the fl ame
icon (fi g. 25). In the case of a request for domestic hot water, the dis-
play (2 - fi g. 3) will show the temperature of the domestic water, the
DHW mode icon and the fl ame icon (fi g. 26).
Adjustment of the heating water temperature
To adjust the heating water temperature, turn the knob with the
symbol (fi g. 27) clockwise in the area marked with + and -.
Summer: turn the selector onto the summer symbol
activate the traditional function of domestic hot water only. In the case
of a request for domestic hot water, the display (2 - fi g. 3) will show the
temperature of the domestic water, the DHW mode icon and the fl ame
icon (fi g. 26).
Pre-heating (faster hot water): turn the domestic water temperature
adjustment knob (fi g. 29) onto the
ing function. The display (2 - fi g. 3) will show the fi xed
the domestic hot water temperature adjustment knob back to the re-
quired position.
This function keeps the water in the domestic hot water exchanger hot,
to reduce standby times when a request is made.
The display indicates the outlet temperature of the heating water or the
domestic hot water based upon the request in progress. During burner
ignition following a pre-heating request, the display shows the fl ashing
symbol and the fl ame icon (fi g. 30).
To deactivate the pre-heating function, rotate the domestic hot water
temperature adjustment knob back to the
required position.
This function cannot be activated when the boiler is OFF: function se-
lector on
OFF (fi g. 34).
Adjustment of the domestic hot water temperature
To adjust the domestic water temperature (bathrooms, showers, kitch-
en, etc.), turn the knob with the
with + and -. The boiler remains in standby until the burner ignites in
response to a heat request. The display shows the domestic water
temperature, the DHW mode icon and the fl ame icon (fi g. 26). The
boiler continues to function until the temperatures set on the boiler are
reached, or the heat request terminates; it will then go back to standby.
If the digital display shows the
means the boiler is in a temporary stop condition (see the "Operating
Mynute Sinthesi C.S.I.
(fi g. 24a) to
symbol to activate the pre-heat-
symbol. Bring
symbol, and then to the
symbol (fi g. 28) in the area marked
icon and an alarm code (fi g. 31), this
11
Publicidad
