To Operate The System With The Time Switch (Optional) - BMW 3 Serie Manual De Instrucciones

F 46 0174 M
To check the mode (auxiliary heating or
ventilation) using the remote control (2)
•
Press the ON and OFF buttons (3 and 1)
simultaneously and hold them:
– The control light (4) is red = auxiliary heating
mode
– The control light (4) is green = auxiliary
ventilation mode
The control light (4) will go out when you release
the buttons or after 10 seconds.
To set the mode (auxiliary heating or ventilation)
using the remote control (2)
•
Press the ON and OFF buttons (3 and 1)
simultaneously twice:
– When you press the buttons (3 and 1) the
first time, the control light (4) will be lit in the
colour of the set mode.
– When you press the buttons (3 and 1) the
second time, the control light (4) will change
colour (and therefore the operating mode)
and will remain lit until you release the
buttons (3 and 1).
If you do not press the ON and OFF buttons (3 and
1) for over 1 second, the setting will be saved.
To set the operating time of the auxiliary heating
or ventilation system using the remote control (2)
The operating time of the auxiliary heating or
ventilation system can be set in 10 minute stages
using the remote control (2). The operating time
should be set to correspond with your driving time
(for example if you have a drive of 30 minutes, the
operating time should not exceed 30 minutes)
The default setting for the operating time is
30 minutes.
•
Briefly press the ON and OFF buttons (3 and 1)
simultaneously three times in sequence:
– The control light (4) will flash to show the set
operating time:
1 flash = operating time 10 minutes
2 flashes = operating time 20 minutes
3 flashes = operating time 30 minutes
4 flashes = operating time 40 minutes
5 flashes = operating time 50 minutes
6 flashes = operating time 60 minutes
– Call up the next operating time using the OFF
button. The operating time will be saved if you
do not press a button for 10 seconds or as soon
as the ON button (3) is pressed.
•
If you press the ON and OFF buttons (3 and 1)
simultaneously until the control light goes out,
the remote control (2) default setting (30 minutes)
will be set.
To switch on the auxiliary heating or ventilation
system using the remote control (2)
Before you leave the car, you must complete
the initial settings (see section 12.1).
38
•
Hold the remote control (2) with the aerial vertical
and press the ON button (3) for longer than
2 seconds.
The auxiliary heating or ventilation system is now
switched on and will continue to operate for the
duration of the operating time. After this the
auxiliary heating or ventilation system will be
switched off automatically.
To switch off the auxiliary heating or ventilation
system before the end of the operating time
using the remote control (2)
•
Hold the remote control (2) with the aerial
vertical and press the OFF button (1) for longer
than 2 seconds.
The auxiliary heating or ventilation system is now
switched off.
12.3 To operate the system with the time
F 46 0175 M
To switch on the auxiliary heating system
Manual: Press the Heat immediately
Automatic: Program the heating start time.
Operating indicator
The Heating indicator
indicator light will be lit throughout the heating
time.
To switch off the auxiliary heating system
Manual: Press the Heat immediately
(4).
Automatic: By the heating time programmed using
the time switch.
The Heating indicator
indicator light will go out.
.
If the auxiliary heating system was switched on
using the Telestart remote control, the auxiliary
heating system can be switched off by pressing
the Heat immediately
To set the time
Press the Time
"Forwards"
desired time is displayed.
Release the button again.
clock will run.
To call up the time
Press the "Time"
will go out after 10 seconds.
To program the heating start time
Three different start times can be programmed.
Press the
start time as follows.
"-:--" or a time will appear on the display (6).
Press "Forwards"
until the required time is shown in the display (6).
The heating start time will be deleted from the
display after approx. 8 seconds.
If you do not press "Forwards"
switch (optional)
(5) and the orange
(5) and the orange
button (4) twice.
button (8) briefly, then press
(1) or "Backwards"
The longer you hold the button, the faster the
button (8) briefly. The display
button (2) once and program the first
Set
(1) or "Backwards"
button (4)
button
(3) until the
(3)
(1) or