lifter CX 14 Manual De Uso Y Mantenimiento página 18

USE (18.18)
The driver must carry out the following instructions of use in the driving position in way to remain reasonably distant from the dangerous zones (such as masts, forks,
chains, pulleys, driving and stabilizing wheels and any other movable part), that can cause the crushing of hands and/or foots.
Safety Regulations
The truck must be used according to the following regulations: a) The driver of the machine must be properly trained, must know the instructions for use of the
vehicle and wear appropriate clothing and a helmet. b) The driver responsible for the fork lift truck must not allow unauthorized personnel to drive the truck or to step
onto the forks or the platform. c) While the truck is in movement the operator must reduce speed in curves, in narrow corridors, through doors or on irregular
surfaces. He must keep unauthorized personnel away from the area where the truck is working and immediately warn people if they are in danger; if, in spite of this
warning there is still someone in the work area the driver must immediately stop the truck. d) It is forbidden to stop in areas where there are moving parts and step
on the fixed parts of the truck. e) The driver must avoid sudden stops and fast inversions of movement. f) In case of slopes with maximum permitted inclination, the
driver must keep the load above the truck and reduce speed. g) When driving the driver must make sure that visibility is good and that there are no obstructions
when reversing. h) If the truck is transported in lifts he must enter them with the loading forks in front (first make sure the lift has a sufficient load). i) It is absolutely
forbidden to disconnect or dismount the safety devices. If the truck is used in areas with a high risk of fire or explosion, it must be approved for this kind of use. j) The
loading capacity of the truck must in no case be exceeded. The driver must ensure that the load is well placed on the forks and in perfect order; the load must not jut
out more than 50mm from the end of the forks. k) Before beginning work the driver of the truck must check: - the performance of the service and parking brake - that
the loading forks are in perfect order - that the wheels and the rollers are not damaged - that the battery is charged, well fixed and the elements perfectly dry and
clean - that all the safety devices are in working order. l) Once the battery (ref. 7/fig. 3) signals that it only has 20% charge left, the trolley/truck must stop being used
and, therefore, recharged. m) The truck must always be used or parked sheltered from rain and snow and in no case must it be used in very damp areas. n)
Temperature of use -10°, +40°. o) Do not use the truck to tow trailers or other trucks. p) Immediately report damages, failures on malfunctions to the responsible
personnel. Do not use the truck until it is repaired. q) Drivers without the required license cannot repair the truck, furthermore they are not authorized to deactivate or
modify the safety devices and switches..
THE MANUFACTURERS SHALL NOT BE HELD LIABLE IN CASE OF FAULTS OR ACCIDENTS DUE TO NEGLIGENCE, INCAPACITY, AND INSTALLATION
BY UNQUALIFIED TECHNICIANS AND IMPROPER USE OF THE TRUCK.
Movement
Before moving the truck check that the horn and the brake work and that the battery is completely charged. Turn the key to the 1 position and move the steering bar
to its movement position. Turn the governor slowly and move towards the relative work area. To brake or stop turn the governor in the opposite direction. Always
steer the truck slowly as sudden movements can provoke dangerous situations (particularly when the truck moves at high speeds). Always drive with the load in a
low position, reduce speed in narrow corridors and on curves.
Mode of use with reduced speed ("Creep speed")
To use the truck in narrow spaces or to handle with precision delicate goods, it is possible to use the truck in "creep speed mode". Creep speed mode is available
only with the tiller bar completely raised. To use the truck with creep speed mode, keep pressed the dedicated button on the rear part of tiller head (ref. 8/fig. 3) on
which is impressed a pictogram of a tortoise and operate on translation and forks moving controls as in standard mode.
"Standard" mode (Only for Evo version)
Allows to increase the battery life by limiting the maximum speed to 5 km/h. It's use is advised to inexperienced users who use the truck occasionally.
"Boost" mode (Only for Evo version)
Favors the truck performance to reduce the working time. The truck moves al the maximum allowed speed of 6 km/h. It is recommended for experienced users, who
use the truck frequently.
WARNING: When the load is lifted steering and braking maneuvers must be carried out slowly and very carefully.
Lift locking device (28.2)
The lift truck is provided with an automatic device which stops the lifting if the batteries reach a discharge rate over 80%. The action of this device is shown by the
red led on the battery level indicator.
If this device intervenes, it is necessary to drive the truck to a battery charger and act as described in the section "Battery charging".
Controls (19.14) - (see fig.3)
1) Accelerator; 2) Dead man's handle; 3) Audible detector pushbutton; 4) Raising button; 5) Lowering button; 6) Master switch; 7) Battery warning light; 8) Creep
speed button (reduced speed); 9) Battery status and hour-counting display; 10) "Boost"
MAINTENANCE (20.9)
Maintenance must be carried out by specialized personnel. The truck must undergo a general check up at least once a year. After every maintenance operation the
performance of the truck and its safety devices must be checked. Inspect the truck periodically so as not to risk the machine stopping or danger for personnel! (see
maintenance table). Note: Disconnect the master switch before carrying out any maintenance operation.
Maintenance table
E LE M E N T
Check lo ad bearing elements
STRUCTURE A ND FORKS Check nuts and bo lts are tightened
Check o f bro nze bushes
Check perfo rmance
B RA KES Check lining fo r wear
Check braking po wer
Check play (abo ut 0,4 mm)
Check wear
WHEELS Check bearing play
Check ancho rage
Check play
STERING B A R Check sideways mo vement
Check return to vertical po sitio n
Check wear o f remo te co ntro l switch
Check co nnectio ns, cable tro uble
Check master switch
ELECTRICA L SYSTEM Check ho rn
Check dead man's butto n
Check fuse values
Check perfo rmance
Check o il level
HYDRA ULIC SYSTEM Check fo r leaks and wear o f
co nnectio ns
Change o il/filter
Check perfo rmance o f pressure
limiting valve
Check flo w limiting valve
Lubrication table
LUB R IC A T IO N
P O IN T S LUB R IC A T O R
WHEELS A ND ROLLERS Lithium grease NLGI-2
GEA RS Oil visco sity 40°C cSt1 43
HYDRA ULIC UNIT Oil visco sity 40°C cSt32
E V E R Y
C H E C KS
3 M ON T H S 6 M ON T H S 12 M ON T H S
●
●
●
●
●
●
●
●
●
●
●
●
●
●
KIN D O F E V E R Y
3 M ON T H S 6 M ON T H S
●
●
button.
E LE M E N T
GEA RS
CYLINDER
●
ELECTRIC M OTORS
●
●
●
B A TTERY
●
●
INSP ECTIONS
●
●
CLEANING THE TRUCK: Clean the parts of the truck, except electrical and electronic
elements, w ith a damp cloth. Do not use direct jets of w ater, steam or inflammable
●
liquids. Clean electrical and electronic components w ith dehumidified compressed air at
●
low pressure (max. 5 bar) or w ith a non metallic brush.
●
Use hydraulic oil apart from m otor and brake oil.
12 M ON T H S
Note: respect the environm ent w hen discarging the used oil. The oil should
be stored in adrum that should be consigned to the nearest collecting
station. Do not dum p the oil in the ground or in unsuitable places.
●
11
C H E C KS
3 M ON T H S
Check no ise level
Change o il
Check perfo rmance leaks and wear
o f gaskets
Check pulleys
Check wear o f brushes
Check starting mo to r relay
Check electro lyte density and level
(no t necessary fo r gel batteries)
Check vo ltage o f elements
Check ancho rage and ho ld o f terminals
Check cables
Grease terminals with Vaseline
Check co nnectio n to electrical circuit
earth
Check ascent and descent speed o f
lifting fo rks
Check safety devices
Test raising and lo wering with no minal
lo ad
E V E R Y
6 M ON T H S 12 M ON T H S
●
●
●
●
●
●
●
●
●
●
●
●
●
●
●