Publicidad
E n g l i s h
Installing the CNS-1 Shield / Visor
1. Adjust a shield / visor to fully opened position and
insert shield / visor hook (C) as per Drawing 4.
2. Press arrowed areas of a shield / visor indicated
in Drawing 5 until it clicks. Then, insert hooks (A)
and (B) securely into positions indicated in
Drawing 6.
3. Do in the same manner for the other side.
4. Open and close a shield/visor a few times and
make sure that all the hooks are fixed securely.
WARNING
If the hook and gear are not securely fastened in the
shield/visor base, the shield/visor may come loose
while riding and an accident may unexpectedly
occur. After installing the CNS-1 shield/visor, open
and close the shield/visor a few times to confirm that
the hook and gear fit securely. With the shield/visor
completely closed, confirm that the shield/visor tab is
clasped by the hook.
F r a n ç a i s
Installation de l'écran CNS-1
1. Ajustez l'écran en position complètement ouverte
et insérez le crochet (C) de l'écran tel qu'indiqué
sur le Schéma 4.
2. Appuyez sur les zones fléchées de l'écran tel
qu'indiqué dans le Schéma 5 jusqu'à ce que vous
entendiez un déclic. Ensuite, insérez les crochets
(A) et (B) fermement dans les positions indiquées
dans le Schéma 6.
3. Opérez de la même manière pour l'autre côté.
4. Ouvrez et fermez l'écran à plusieurs reprises pour
vous assurer que tous les crochets sont correcte-
ment fixés.
ATTENTION
Si les crochets et l'engrenage ne sont pas
fermement fixés à la base de l'écran, celui-ci peut se
détacher en roulant, ce qui peut causer un accident
de manière imprévisible. Après l'installation de
l'écran CNS-1, ouvrez et fermez l'écran à plusieurs
reprises,
afin
de
vérifier
que
le
crochet
l'engrenage de l'écran sont correctement fixés. Une
fois l'écran complètement fermé, vérifiez que l'ergot
de l'écran est bien maintenu par le crochet.
9
4
Hook rail
Rail de fixation
Hook (C)
Crochet (C)
5
Shield / Visor
Écran
Hook (B)
Crochet (B)
Hook (A)
Crochet (A)
6
et
E n g l i s h
Important Notice about Handling the CNS-1 Shield / Visor
1. Dirt and scratches on the shield / visor may
obstruct your view while riding and can be
very dangerous! If the CNS-1 shield / visor
gets dirty or scratched, stop using it
immediately. Remove the shield /visor and
clean or replace it.
2. The CNS-1 shield / visor should be cleaned
with a solution of mild, neutral soap and
water. Rinse well with pure water then wipe
dry with a soft cloth. Do not use any of the
following cleaning materials: hot water
over 40℃; salt water; any acidic or alkali
detergent; benzine, thinner, gasoline, or
other organic solvents; glass cleaner; or
any cleaner containing organic solvents. If
any
of
these
cleaners
are
used,
the
shield's / visor's chemical nature may be
altered and safety may be hindered.
3. Do not ride with a shield / visor that is fogged.
This may obstruct your view and can be very
dangerous. If the CNS-1 shield / visor is
fogged, open the lower air intake to circulate
air within the helmet and remove the fog from
the shield / visor. Use of the PINLOCK
EVO
©
lens is also effective in stopping fog.
4. Always use SHOEI's genuine PINLOCK
EVO
©
lens for CNS-1. For fitting PINLOCK
EVO
©
lens, please read instructions enclosed in it.
5. Remove the protective film before using the
shield / visor for the first time.
WARNING
CNS-1 tinted shield/ visor is not for sale or use
in USA.
If tinted shield / visor and sun visor are used
together in USA, requirement of light transmission
ratio specified in VESC-8* is not satisfied. Don't
use tinted shield /visor to your helmet in a manner
not satisfying VESC-8*. Otherwise, your vision
restricted by tinted shield/visor may cause an
accident and serious injury or death.
6. After cleaning or replacing the base plates,
close the shield / visor and make sure that it
touches the window beading in all around. If
there is a gap between the shield / visor and
the window beading, adjust a position of the
base plate and eliminate the gap, because it
may cause roll-in of wind or noise.
7. For tightening screws, apply No.2 size Phillips
head screwdriver vertically and rotate it
carefully. If improper sized screwdriver or
electric screwdriver is used, a screw head
may be broken. Use a genuine screw made of
aluminum for replacement. If a screw is
tightened too much, it may be broken.
(Recommended torque: 80 cN . m or about 8
kgf . cm)
Size
(No.2)
8. Do not place any sticker or tape in the
shield's / visor's field of vision.
NOTE ;
VESC-8: Vehicle Equipment Safety Commission
regulation NO.8 for motorcyclist eye protection
This standard is widely referenced and applied by
the 36 states in USA with motorcyclist eye
protection use law.
10
Publicidad
Capítulos
