Brake Pedal; Accelerator Pedal - Honda HF2317 Manual De Instrucciones

fuel in reserve: indicates that there are about 1.5 litres left in
h)
the tank, sufficient for about 30-40 minutes of normal work.
headlights on;
i)
– i.1) The sensor inside the control panel controls the auto-
matic switching on of the headlights after a few seconds
of darkness and their switching off after a few seconds
of brightness. To avoid unwanted switching on, keep the
sensor area clean and do not place any rags or objects
on the control panel.
The brightness level of the headlights may drop for a few
seconds due to a power-loss during start-up.
WARNING!
Do not look directly at the LED headlight.
It may adversely affect the eyes.
j) transmission in "neutral".
k) engine lubrication anomalies: stop the engine immediately,
check the oil level (5.3.3) and contact your dealer if the
problem persists.
l) The inclination of the machine has reached a non-recom-
mended gradient
NOTE
the user to know the angle of inclination of the machine. The
light may light up in the event of abrupt start/stop or sudden
steering. Avoid these types of actions.
NOTE
lowing the assembly instructions described in the manual
otherwise the tilt indicator may not work properly.
The light timing of the icon can be influenced by the weight
of the operator, the weight of the grass catcher and the tyre
pressure.
It is possible to change the light timing when an optional
accessory is mounted.
The calibration of the sensor used for the light function
must be performed by your service provider in order for it to
function correctly.
NOTE
tions, please contact your Dealer (for example, the icon lights
up with the machine on a flat surface or on a low slope).
m) Maintenance needed.
As soon as the indicator light illuminates, the hourly inter-
vention threshold appears on the display as a code:
M20 = Maintenance in 20 hours
M50 = Maintenance in 50 hours
M100 = Maintenance in 100 hours
M300 = Maintenance in 300 hours
Maintenance work to be performed for each hourly thresh-
old is specified in (
The maintenance code remains on the display until the
engine is turned on or the display functions are changed.
The maintenance light instead remains on regardless of the
engine status or display functions.
If more than one intervention threshold is reached at the
same time, the corresponding maintenance codes alternate
on the display every 2 seconds, in ascending order.
After each maintenance, reset the operation, otherwise both
the intervention code and the icon will remain on the display
and the maintenance interval will not be accurate.
To reset the operation:
This icon is only informative and helps
Assemble all components correctly fol-
If the lamps light up often in wrong situa-
6.2).
– Press and hold "MODE" button (4.13.b) for
more than 10 seconds, with the key in the
«ON» position and the engine off.
The maintenance code and the icon will be displayed again
when the next maintenance hourly threshold is reached.
If the maintenance instructions are reset before the hourly
intervention threshold is reached, the maintenance sched-
ule is still displayed at the first useful interval. In this case,
reset the operation again if the maintenance has already
been performed.
HF2417•••
If the maintenance instructions cannot be reset immedi-
ately after the engine has stopped, wait until the battery
voltage drops below 12.7V. Then try to check the mainte-
nance code.
HF2625•••
n) Engine RPM indicator: The notches displayed on the
graph scale increase as the engine
The graphic indicator and the numerical value on the
display (a.2) change simultaneously.
o) There are two types of sound warnings:
– continuous signals the intervention of the electronic
circuit board protection; turn the key in
"OFF" position to stop the sound.
– intermittent Grass catcher full alert.

4.21 BRAKE PEDAL

This pedal works the brake on the rear wheels.

4.22 ACCELERATOR PEDAL

This pedal is used to engage the traction to the back wheels in for-
ward drive and adjust the speed of the machine.
- Increasing the pressure on the pedal progressively increases the
speed of the machine.
– The pedal automatically goes into neutral «N» when released.
– The "neutral" condition «N» is shown by the lighting of a pilot lamp
(4.13.j).
increases.
RPM
11 EN