Talsa W22 Manual De Instrucciones página 22

MINCERS / GRINDERS
4. STORAGE, TRANSPORT and DELIVERY
The machine is delivered on a pallet protected by cardboard packaging. We use
only recyclable packaging and ask that you please recycle these materials.
Unpack and carefully inspect the machine upon delivery. If the machine is
damaged, note this on the delivery receipt, retain all packing materials and
promptly notify the carrier. The carrier assumes sole responsibility for damage
sustain during transit.
If the machine is found to be in good condition, convey it to a suitable work area
with a stable, flat and level surface. Since these machines can be very heavy (see
the above Technical Specifications), we always recommend the use of a pallet
mover or forklift.
The packaging contents are as follows:
 TALSA mincer/grinder.
 Solid feed stomper.
 Extracting wrench for the worm.
 Instruction manual.
 CE declaration of conformity (for units shipped within the EU
or countries belonging to the CEN).
 Enterpise / Unger-2 models: 1 single cutting knife. 2 cutting
plates with hole diameters 4,5 (5) and 7,8 mm.
Feed stomper
5. INSTALLATION
1. Place the mincer/grinder in a clean work area that is free of obstacles and that
has a level, skid-free, flat surface. If the mincer/grinder is a table model, it must
be mounted on a stable surface that is sturdy enough to support its weight. The
work area must be well-lit and have adequate ventilation. Leave enough space
around the machine to facilitate its use, cleaning, and maintenance.
Position the machine so that the power cord's plug is easily accessible to the
user. The plug must conform to local electrical standards and be suitable for
use with this type of machine.
2. Inspect the feed pan's hand guard to make certain that it has not been bent or
dented during transport. DO NOT use the mincer/grinder if the hand guard is
damaged in any way.
3. Consult the machine's specifications plate or section 3 (
) to verify that the motor specifications (voltage, frequency,
SPECIFICATIONS
etc.) match the electrical service at the workplace. The line voltage must be up
to specification. Rated voltage shall be identical with full supply voltage.
PLEASE NOTE: there is a tolerance of ±10% for voltage and of ±2% for
frequency.
a) If the machine's voltage is not compatible with your electrical service AND
the machine has a three-phase, dual-voltage motor, proceed with the
instructions in section 6 (
b) If the machine's voltage is not compatible with the electrical service and it
is not equipped with a dual-voltage motor, call a qualified electrician to
resolve the incongruity.
c) If the machine's voltage is compatible with your electrical service, proceed
with the instructions in Section 7 (
(
Estimated time: 45 minutes)
).
CHANGING THE VOLTAGE
OPERATING INSTRUCTIONS
• Always keep the machine upright, even
while in its packaging.
• NEVER stack machines on top of each
other. NEVER place heavy objects on top
of the machines or its packaging.
•
DO NOT pull or push on the throat of the
mincer/grinder when unpacking or moving
the machine.
Additionally:
 Unger-3 models: 1 double cutting knife, 1 pre-cutting plate, 1
supplementary ring to use as Unger-2 system (1 plate and 1
knife).
 Unger-5 models: 2 double cutting knives, 1 pre-cutting plate,
1 plate with holes diameter 3 mm, 2 supplementary rings to
use as Unger-2 (1 plate and 1 knife) or Unger-3 system (2
plates and 1 double cutting knive).
• This machine must be installed only by a
qualified technician and in compliance with
applicable national, regional and local
electrical, safety, hygiene and building
codes.
• The workplace electrical wiring should be
equipped
differential residual circuit breakers to fully
protect against power surges. A qualified
electrician must adjust these safety
TECHNICAL
devices to the specifications of your
particular machine.
Check the wiring before plugging the
machine to the electrical outlet! The power
cord's wiring is normally assigned as
follows: PHASES: black, brown or gray.
GROUND: bi-colored yellow/green or just
green in some non-CE/CEN/UE countries.
).
EN-21
Warning!
Extracting wrench
Electrical Hazard!
with magneto-thermic
Important!
MANUAL
and