Memory Switch; Operating Procedure; Memory Switch List - JUKI MEB-3200 Manual De Instrucciones

14. MEMORY SWITCH

(1) Operating procedure

1
2
3

(2) Memory switch list

No. Function
1 Soft-start speed settng
1st sttch (Insde needle → outsde needle)
2 Soft-start speed settng
1st sttch (outsde needle → nsde needle)
3 Soft-start speed settng
2nd sttch (nsde needle → outsde needle)
4 Soft-start speed settng
2nd sttch (outsde needle → nsde needle)
5 Soft-start speed settng
3rd sttch (nsde needle → outsde needle)
6 Soft-start speed settng
3rd sttch (outsde needle → nsde needle)
7 Needle thread tenson settng at the tme of
thread trmmng
8 Looper thread tenson settng at the tme of
thread trmmng
9 Needle thread tenson settng at the tme of
machne-stop
10 Looper thread tenson settng at the tme of
machne-stop
11 Set poston selecton
Orgn poston/Front
12 Producton counter selecton
Wthout/UP/DOWN
13 Selecton of startng when producton
counter s "0"
Permtted/prohbted

6
4
5
Lmted speed at the sewng start of the sewng machne
s set. From nsde needle to outsde needle of 1st sttch
Lmted speed at the sewng start of the sewng machne
s set. From outsde needle to nsde needle of 1st sttch
Lmted speed at the sewng start of the sewng machne
s set. From nsde needle to outsde needle of 2nd sttch
Lmted speed at the sewng start of the sewng machne
s set. From outsde needle to nsde needle of 2nd sttch
Lmted speed at the sewng start of the sewng machne
s set. From nsde needle to outsde needle of 2nd sttch
Lmted speed at the sewng start of the sewng machne
s set. From outsde needle to nsde needle of 3rd sttch
Needle thread tenson value at the tme of thread
trmmng s set.
Looper thread tenson value at the tme of thread trmmng
s set.
Needle thread tenson value at the tme of machne-stop
s set.
Looper thread tenson value at the tme of machne-stop
s set.
Poston of presser when settng cloth s selected.
0 : Orgn poston
1 : Front poston (Poston s set at No. = 29.)
Operaton of producton counter s selected.
0 : Wthout
1 : UP counter (" ＋ 1" per sewng cycle)
2 : DOWN counter (" − 1" per sewng cycle)
Whether prohbtng startng at count value "0" when
producton counter s set to DOWN counter s selected.
0 : Startng permtted even when producton counter
value s "0"
1 : Startng prohbted when producton counter values "0"
Pressing [READY
power and the mode becomes the memory
switch mode. Then various data can be changed.
1) Select memory swtch No. wth [LEFT
or [LEFT ] key 3 .
2) Change the set value wth [RIGHT
[RIGHT ] key 4 .
3) Repeat the steps 1) to 2) when changng other set values.
4) After completon of settng, press [READY
key 1 to make the set value store n memory and
the memory swtch mode ends.
When [RESET
mode ends without storing the set value
in memory. When turning OFF the power
without pressing [READY
setting is not stored in memory.
Description
] key 1 , turn ON the
] key 2
] key 5 or
] key 6 is pressed , the
] key 1 , the
Setting Setting Initial
range unit value
400 to 1,200 100 600
st/mn st/mn
400 to 2,200 100 600
st/mn st/mn
400 to 2,200 100 600
st/mn st/mn
400 to 2,200 100 600
st/mn st/mn
400 to 2,200 100 600
st/mn st/mn
400 to 2,200 100 600
st/mn st/mn
0 to 255 1 0
0 to 255 1 0
0 to 255 1 60
0 to 255 1 0
0 to 1 - 0
0 to 2 - 1
0 to 1 - 1
]