Error List - JUKI MEB-3200 Manual De Instrucciones

15. ERROR LIST

No.
1 Sewng machne motor error
Sewng machne motor doses not run or sgnal does not enter even
when t s runnng.
3 Looper thread trmmng knfe return error
When the looper thread trmmng knfe has not returned at the tmre of
operaton of the sewng machne or operaton of looper thread trmmng
4 Lengthwse drecton steppng motor orgn sensor error
When lengthwse drecton orgn sensor has not changed at the tme
of orgn retreval
5 Crosswse drecton steppng motor orgn sensor error
When crosswse drecton orgn sensor has not changed at the tme
of orgn retreval
6 Turnng steppng motor orgn sensor error
When turnng orgn sensor has not changed at the tme of orgn retreval
7 Cloth cuttng knfe steppng motor orgn sensor error
When cloth cuttng knfe orgn sensor has not changed at the tme of
orgn retreval
8 Ar pressure lowerng error
When ar pressure s lowered
9 Head safety swtch error
When the sewng machne s operated wth machne head rased
10 Temporary stop swtch
When temporary stop swtch s pressed whle the sewng machne s
operated
12 Needle UP error
When the needle bar s not n the upper poston of the nsde needle sde
20 Presser type error
Data settng and presser type (thread trmmng type) are dfferent
from each other
21 Data settng range error
Outsde of settng range error at the tme of data settng
22 Data settng sewng length error
Sewng length s over the sewng possble area at the tme of data settng.
23 Thread tenson settng range error
Outsde of settng range error at the tme of thread tenson settng
24 Data settng bartack duplcaton
Taper bar, straght bar and round bar are duplcated.
25 Settng range error of compensaton of number of sttches at the end
of sewng at the tme of data settng of straght bar
29 Cycle sewng pattern error
Pattern No. s not set n cycle sewng.
90 Presser type settng error
Settng of DIP-SW of presser type s wrong.
91 Backup memory error
When backup data such as pattern No. or the lke has not been
stored n memory
92 Memory swtch error
When data of memory swtch has broken
93 Pattern data error
When pattern data has broken.
97 Defectve feed error
When synchronzaton of the sewng machne and the feed s not obtaned
98 Fan error
Error due to temperature detecton nsde the control box
99 EEPROM wrte-n error
Defectve wrte-n at the tme of memory swtch or pattern data wrtng
0
Description
Turn OFF the power.
Remove the cause of error and press the RESET key.
Turn OFF the power.
Turn OFF the power.
Turn OFF the power.
Turn OFF the power.
Supply ar and press the RESET key.
Return the machne head to ts home poston and
press the RESET key.
Press the RESET key.
Upper poston detecton by turnng handwheel by hand
Perform pattern change/data change after pressng
the RESET key.
(Note 1)
Change the data after pressng the RESET key.
(Note 2)
(Note 3) Change the data after pressng the RESET key.
(Note 4) Change the thread tenson after pressng the RESET
key.
Change the data after pressng the RESET key.
Change the data after pressng the RESET key.
Perform pattern change/cycle sewng settng after
pressng the RESET key.
(Note 5) Turn OFF the power. Change over the DIP-SW.
Backup data wll be ntalzed after pressng the
RESET key.
Memory swtch data wll be ntalzed n machne
model settng after pressng the RESET key. Note 6
Pattern data wll be ntalzed after pressng the
RESET key.
Turn OFF the power.
Turn OFF the power. Clean the fan of the control box.
Turn OFF the power.
How to reset