Quattro QUATTRO400-001 Guia De Instalacion página 5

Install the Isolation Switch (29) between the battery and the Control Unit on the positive (+) cable, use two of the
8mm Battery Terminal Connectors (22) to link the cable to the switch terminals. Nuts and bolts are provided to mount
the switch but please substitute as necessary if they are not of a suitable type. Again, it is recommended to use the
supplied Trunking (11) to protect the cables against sharp edges. Attach the trunking with P-Clips (20) and P-Clip
Screws (19).
Connect the Battery Cables to the existing battery terminals (red = positive, black = negative). Two types of Battery
Terminal Connector (22 & 23) are provided for use as appropriate.
Caution! Make sure that you do not reverse the Positive (+) and Negative (-) connections.
Incorrect connection (reverse polarity) will result in damage to the control box.
The length of wiring from one motor and the other must always remain the same, this will prevent a performance
difference (due to voltage drops) from one side to the other. Fix the spade connectors using crimping pliers. A secure
and good quality connection on each cable is essential.
Finally, connect the Battery Cables (14 & 15) to the Control Unit (1). Installation of your Caravan Mover is now complete.
Operation - Safety Guidelines
Before use, always check the mover for any damage.
When towing or moving the caravan please be aware, at all times, that ground clearance is reduced by
50mm when the Mover has been fitted.
To maintain signal strength, always ensure that during manoeuvring the distance between the remote
control and the caravan does not exceed 5 metres.
DO be aware that the mover increases your caravan or trailer weight. So this reduces the payload of
the caravan.
DO always make sure that the rollers are fully disengaged from the tyres when the mover is not in use.
This is better for the tyres and for the mover.
DO always make sure that the rollers are fully disengaged before towing/moving the caravan by
vehicle or manpower. This can damage the tyres, mover and the towing vehicle.
DO always make sure that after you have finished using the Mover, the Battery Power Isolation Switch
(29) is switched off and the key is removed and stored in a safe place (out of reach of children or other
unauthorised people).
DO always make sure that the remote control is stored in a safe place (out of reach of children or other
unauthorised people).
DO always apply the handbrake after manoeuvring, before disengaging the drive rollers from the tyres.
DO always ensure that children and pets are kept well out of the way during operation.
DO NOT rely on the mover to act as a brake.
DO NOT exceed the total Safe Working Load (SWL).
DO NOT make any modifications on the caravan mover (mechanical or electronically). This can be
very dangerous! No warranty caim will be accepted and we cannot guarantee the function of the mover
if any modifications are made. We will not be liable for any damage whatsoever caused as a result of
incorrect installation, operation or modification.
Operation - First Use
The mover has two Motor Units (Installation Manual 1 & 2). In general they are mounted in front of the axle of
the caravan/trailer. Both units are identical, so either can fitted to nearside or offside framework. Please refer to
appropriate installation manual that is packaged in with your mover framework.
EN 08
(Fig.2 - Installation Manual) A: Drive Roller
B: 12V Motor
C: Connection Terminals (+ and -)
D: Base Unit
E: Drive Unit
F: Gear Housing
Always ensure that you are close enough to engage the caravan's handbrake when manoeuvring
on uneven terrain and gradients/slopes in case of mechanical failure. Do not use the mover as
a brake, when you have finished manoeuvring always engage the caravan's handbrake, and
disengage the movers when not in use.
SAFETY FIRST! Ensure that there are no persons or obstructions in the vicinity of the caravan
prior to testing.
Please make sure you read the safety instructions very carefully and make sure that you follow these guidelines!
Make sure that the battery that supplies the mover is fully charged and in good condition.
Make sure that the caravan is free from the vehicle and the handbrake is on. Also make sure that the
corner-steady feet are fully raised.
Engage both rollers as described in 'Operation-Mover engagement'. For the manual engagement movers this only
needs to be done on one side of your caravan since the other side will automatically follow via the cross actuation bar.
Turn on the Battery Power Isolation Switch (29).
Before operating the Mover, release the handbrake.
Store remote control in a safe place (out of reach of children or other unauthorised people.
Operation - Remote Control Handset First Use
The Remote Control handset (2) is powered by two 'AA' 1.5V batteries (refrain from using lower voltage
rechargables), and is activated by double-pressing the button (Fig.1C). Once activated the display will illuminate. If
the handset has not been used 60 seconds it will power off. Ensure before continuing that the control unit has power
by turning on your isolation key.
Fig.1 A = Handset display
B = Directional thumb stick
C = Multi-function button
After the handset has completed powering on the following home screen will shown on screen. Note if any icons are
flashing this indicates an issue, or that the handset hasn't connected to the control box. Ensure isolation key is turned
on before powering on the handset, and allow up to 10 seconds for a connection to be established.
(A) Signal strength - Indicates signal strength between handset and control unit
A
C
inside the caravan.
D
(B) System status - If a smiling face is showing the system is working correctly.
B
E
(C) Handset battery status - Indicates handset battery level.
(D) Leisure battery status - Indicates voltage level of leisure battery, for
maximum performance ensure battery is fully charged and showing 4 bars before
Caravan orientation flipped &
operating mover.
Handset searching for signal
(E) Mover orientation - This shows the direction of travel of the caravan, when
the thumb stick is moved the caravan will follow in this direction. By default the
hitch is designated as the forward direction. At any time press the multi-function
button (Fig.1C) to flip the caravan orientation, the rear of the caravan will then
move forward when the thumb stick is moved upwards.
- If a magnifying glass is showing, the handset is waiting to pair.
- If an 'E' number is showing refer to page 13 for error diagnosis.
EN 09