Routine Maintenance; Cutting Procedures; Cleaning The Air Filter; When Work Is Finished - GGP ITALY SHT 660 K Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 79
nerates an average sized
field, but it is not however possible to ex­
clude the possibility of interference on any
active or passive medical devices that opera­
tors may be wearing; this could be risky for
their health conditions. All those using medi­
cal devices should always consult their GP,
or the device manufacturer, before using this
machine.
WARNING!
Always wear suitable cloth­
ing when using the machine. Your Dealer can
provide you with all the information on the
most suitable accident­prevention devices to
guarantee your safety.
WARNING!
If something breaks or an
accident occurs during mowing, turn off the
engine immediately and move the machine
away to prevent further damage; if an ac­
cident occurs with injuries or third parties
are injured, carry out the first aid measures
most suitable for the situation immediately
and contact the medical authorities for any
necessary health care. Carefully remove any
debris that might cause damage or harm per­
sons or animals should it not be seen.

3.1 CUTTING PROCEDURES

WARNING!
When cutting, always hold
the machine firmly with both hands.
WARNING!
Immediately stop the machi­
ne if the blades block while running or if they
get caught up in the hedge branches.
It is recommended to trim the two vertical sides 
of the hedge before trimming the top.
Adjust  the  machine's  handgrip  according  to  the 
type of cutting (see 1.4).
3.1.1 Vertical cutting (Fig. 6)
Proceed  by  cutting  using  curved  movements 
from  the  bottom  towards  the  top,  keeping  the 
blade as far from the body as possible.
3.1.2 Horizontal cutting (Fig. 7)
The best results will be obtained with the blade 
slightly inclined  (5° - 10°) in the direction you are 
cutting, proceed with a curved movement, slowly 
and without interruptions, especially in the case 
of very thick hedges.

3.2 WHEN WORK IS FINISHED

electromagnetic
11
When you have finished your work:
–    S top the machine as indicated previously (see 
2.3).
– Wait for the blades to stop and replace the pro-
tection device.

4. ROUTINE MAINTENANCE

Correct  maintenance  is  essential  to  maintain 
the original efficiency and safety of the machine 
over time.
WARNING!
During maintenance opera­
tions:
– remove the spark plug cap.
– Wait until the engine is sufficiently cold.
– Use protective gloves when handling the
blades.
– Keep the blade protection devices on,
except when intervening directly on the
blade.
– Never dispose of oils, fuel or other pollut­
ing materials in unauthorised places.
4.1 STORAGE
At  the  end  of  each  working  session,  carefully 
clean the machine of dust and debris, and make 
sure  that  there  are  no  damaged  parts;  replace 
any faulty parts and lubricate the blades to pre-
vent rust.
The  machine  must  be  preserved  in  a  dry  area, 
protected  from  all  weather  conditions  and  with 
the blade protection device correctly fitted.
4.2 CLEANINGTHE ENGINE
AND THE SILENCER
To reduce fire risks, periodically clean the cylin-
der fins with compressed air and clear the silenc-
er area from branches, leaves or other debris.

4.3 CLEANING THE AIR FILTER

IMPORTANT Cleaning the air filter is essential
to guarantee the efficiency and duration of the
machine.
It  must  be  cleaned  after  every  8-10  working 
hours.
To clean the filter (Fig. 8):
–    L oosen the knob (1) remove the cover (2) and 
the filter element (3).
–    W ash the filter element (3) with soap and wa-
ter. Do not use petrol or other solvents.
–    L eave the filter to dry in the open air. 

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Sht 675 k

Tabla de contenido