Starting The Machine; Cold Starting - GGP ITALY SHT 660 K Manual De Instrucciones

Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 79
– Never smoke whilst preparing the mixture
and avoid inhaling the petrol fumes.
To prepare the fuel mixture:
–    P lace about half the amount of petrol in a ho-
mologated tank.
– Add all the oil.
– Add the rest of the petrol.
–    C lose the top and shake well.
IMPORTANT The  fuel  mixture  tends  to  age.  Do 
not prepare excessive amounts of the fuel mixture 
to avoid the formation of deposits.
IMPORTANT Keep  the  petrol  and  fuel  mixture 
containers separate and easily identifiable to
avoid the mistake of using one in place of the
other.
IMPORTANT Periodically clean the petrol and
fuel  mixture  containers  to  remove  any  eventual 
deposits.
1.3 REFUELLING
DANGER!
Never smoke whilst refuelling
and avoid inhaling the petrol fumes
WARNING!
Carefully open the tank top
as pressure could have formed inside.
Before refuelling:
–    S hake the fuel mixture container well.
–    P lace  the  machine  on  a  flat  stable  surface, 
with the fuel tank cap facing upwards.
–    C lean  the  fuel  tank  cap  and  the  surrounding 
area  to  avoid  any  dirt  from  entering  the  tank 
during refilling.
–    C arefully  open  the  fuel  tank  cap  to  allow  the 
pressure  inside  to  decrease  gradually.  Use  a 
funnel to refill and avoid filling the tank to the 
brim (Fig. 1).
WARNING!
Always close the fuel tank
cap firmly.
WARNING!
Immediately clean all traces
of fuel which may have dripped on the ma­
chine or the ground and do not start the en­
gine until the petrol fumes have dissipated.
1.4 REGULATING THE HANDGRIP (Fig. 2)
The rear handgrip (1) can be adjusted to 3 differ-
ent positions in relation to the cutting device to
make trimming your hedges easier.
WARNING!
The handgrip must only be
adjusted when the engine is switched off.
– Pull the release lever (2) up.
– Rotate the rear handgrip (1) to the desired po-
sition.
–    B efore  using  the  machine  check  that  the  re-
lease  lever  (2)  is  as  low  as  possible,  and  the 
rear handgrip is firmly attached.
WARNING!
handgrip must always be in a vertical posi­
tion, whatever the position of the cutting de­
vice (3).
2. USING THE MACHINE

2.1 STARTING THE MACHINE

WARNING!
The machine must be started
in an area at least 3 metres from where you
refilled the fuel tank.
Before starting the machine:
–    P lace the machine firmly on the ground.
–    R emove the blade protection devices.
–    M ake sure the blade is not touching the ground 
or any other object.
–    M ake  sure  that  the  handgrip  is  locked  in  the 
centre position.

2.1.1 Cold starting

NOTE A "cold" start of the engine means start­
ing it after at least 5 minutes from when it was
switched off or after refuelling.
To start the machine (Fig. 3):
1.    P ress switch  (1) to position «I».
2.    G ently press the bulb (2) on the "primer" 7-10 
times  until  the  fuel  flows  from  the  exhaust 
pipe.
3. Turn the starter control lever (3) to the «B»
position.
4.    H old  the  machine  firmly  on  the  ground  with 
one hand on the handgrip, in order not to lose
control of the machine during startup.
WARNING!
firmly, the force of the engine could cause
the user to lose his balance or direct the
blade towards an obstacle or the same user.
5.    P ull the starter grip slowly for 10 - -15 cm un-
til you feel some resistance, then tug it a few 
times until you hear the engine turn over.
9
When working, the rear
If the machine is not held

Publicidad

Tabla de contenido
loading

Este manual también es adecuado para:

Sht 675 k

Tabla de contenido