Publicidad
Idiomas disponibles
Idiomas disponibles
2.4 - MAIN FEATURES OF THE CONTROL UNIT
-
Automated access command for 1 24V motor.
-
Flasher control with/without integrated intermittency function
(Paragraph 10.3).
-
This output can also be used to control courtesy lights
(Paragraph 13).
-
Inputs for start, stop opening wired commands, (Paragraph
10.7).
-
Double input for safety devices: "S2 Photo" and "S1 Edge"
(paragraph 10.5).
-
Possibility of powering 24VDC accessories (paragraph 10.6).
-
Input for external antenna that can be used for increasing the
range of the transmitters (Paragraph 10.8).
-
Pause time for automatic re-closing adjustable to between 0
and 180 sec. with knob (Paragraph 4.2).
-
Obstacle sensitivity adjustment with knob (Paragraph 4.2).
-
Motor force adjustment with knob (Paragraph 4.2).
-
Incorporated radio receiver (433.92MHz), compatible with
King-Gates rolling transmitters.
-
It is possible to store up to 180 transmitters.
-
6 indication LEDs (Paragraph 8).
-
Slow-speed opening and closing (customizable through
dedicated programming).
3. INSTALLATION
The installation of ROLLS must be carried out by qualified
personnel in compliance with current legislation, standards and
regulations, and the directions provided in this manual.
3.1 - PRELIMINARY CHECKS
Before proceeding with the installation of ROLLS you must:
•
Verify and ensure that, after installation, no door parts
obstruct public roadways or pavements.
•
Check that all the materials are in excellent condition, suitable
for use and that they conform to the standards currently in
force.
•
Make sure that the structure of the gate is suitable for
automation.
•
Make sure that the force and dimensions of the door fall
within the specified operating limits provided in chapter 2.1
("Operating limits").
•
Check that the static friction (that is, the force required
to start the movement of the leaf) is less than half the
"maximum torque", and that the dynamic friction (that is, the
force required to keep the leaf moving) is less than half the
"nominal torque". Compare the resulting values with those
specified in section 17 ("Technical specifications").
The manufacturer recommends a 50% margin on the force, as
unfavourable climatic conditions may cause an increase in the
friction.
•
Make sure that there are no points of greater friction in the
opening or closing travel of the door.
•
Make sure that the mechanical stops are sturdy enough, and
that there is no danger of the door derailing.
•
Make sure that the door is well balanced: it must not move by
itself when left stationary in any position.
- 26 - ENGLISH
•
Make sure that the mounting positions of the various devices
(photocells, keys, etc.) are protected from impact and that the
mounting surfaces are sufficiently sturdy.
•
Make sure that the minimum and maximum clearances
specified in fig. 2 and 3 are complied with.
C
2875 mm
2
B
F6
F4
F5
F2
F3
F1
A (cm)
F1
0
244
2
244
4
244
6
245
8
245
10
12
14
16
18
20
22
24
26
28
30
32
34
3
•
Check and ensure that the manual release is fitted at a
maximum height of 1.8 m.
•
Components must never be immersed in water or other
liquids.
•
Keep all ROLLS components away from heat sources and
open flames; these could damage the components and cause
malfunctions, fire or dangerous situations.
•
If the door includes an access door, make sure that it does
not obstruct normal travel. Fit a suitable interlock system if
necessary.
•
Only insert the ROLLS plug into sockets equipped with a safety
grounding system.
•
The socket must be protected by suitable magneto-thermal
and differential switches.
D
414 mm
0÷400 mm
F2
F3
F4
F5
240
236
232
228
240
236
232
228
240
236
232
228
241
237
233
229
241
237
233
229
242
238
234
230
243
239
234
230
245
240
235
231
241
237
232
243
238
233
245
239
235
241
236
244
238
240
243
F6
224
224
224
225
225
225
226
227
228
229
230
231
233
234
236
239
241
245
Publicidad
