Publicidad
Idiomas disponibles
Idiomas disponibles
11 - ADVANCED PROGRAMMING
The control unit has additional special features not required for
most of standard installations. All descriptions are reported here
below.
12 - BACKJUMP ADJUSTMENT
This procedure allows for adjusting or eliminating the backjump.
It consists in inverting the door movement at the end of the path
to perform belt recovery, facilitate unlocking and safeguard the
mechanical system. On certain installations this is unnecessary,
therefore this value can be adjusted.
DEFAULT: STAR GDO backjump = value 1, equal to 200ms
m
Prior to proceeding with this programming procedure,
first verify whether either the "basic path programming"
or the "advanced path programming" of the automation's
movement have been completed.
1. PUT THE DOOR IN THE CLOSED POSITION
2. PRESS THE START BUTTON FOR 3 SECOND: All the LEDs turn
off (if not, consult Paragraph 15)
3. PRESS THE SET BUTTON FOR 1 SECOND: The yellow "set" LED
turns on in fixed mode and the red "error" LED indicates the
backjump level
4. PRESS THE SET BUTTON FOR 1 SECOND: The yellow "set LED
flashes then turns on in fixed mode and the red "error" LED
indicates the backjump level*
5. EVERY TIME THE SET BUTTON IS PRESSED, THE VALUE
CHANGES FROM 1 TO 6 STARTING FROM THE CURRENTLY
SET VALUE: The yellow "set" LED remains lit in fixed mode
and the red "error" LED indicates the backjump level
6. PRESS THE RADIO BUTTON FOR 2 SECONDS: The yellow "set"
LED remains lit in fixed mode and the red "error" LED flashes
fast
7. PRESS THE SET AND RADIO BUTTONS SIMULTANEOUSLY OR
WAIT 10 SECONDS TO EXIT THE PROCEDURE: The LEDs return
to the normal operation configuration
* The backjump value is indicated by the number of flashes of the
series based on the set value.
Backjump levels: 0 / 200mS / 400mS / 600mS / 800mS / 1Sec.
When the series consists of one flash, the backjump value is zero
(no inversion of movement at end-of-path), when there are 6
flashes, the backjump is set to the maximum value.
Clearly, the other series indicate growing intermediate values from
1 to 6.
The backjump value can be known at any time after the SET
button is pressed the first time, by counting the number of flashes
of the green "photo" LED.
m
If the backjump value is set too high, some undesired
clearance may remain between the door and the mechanical
stop.
- 38 - ENGLISH
13 - AUX OUTPUT PROGRAMMING
These programming sequences are not essential for system
operation, but allow the AUX output to be activated by choosing
the relevant terminals.
m
The AUX output delivers 24Vdc
To interrupt the following programming sequences at any time,
press the SET and RADIO buttons simultaneously or wait 10
seconds.
AUX USED AS COURTESY LIGHT
If the AUX output is used as courtesy light to control the lamps, a
relay must be connected.
The light can be activated via a special transmitter button (to be
programmed as indicated in the relevant paragraph).
SWITCHING ON/OFF OF THE LIGHT THROUGH A DEDICATED
TRANSMITTER BUTTON:
-
connect a monostable relay;
-
set the AUX output on the desired terminals;
-
the work mode is only bistable, ON / OFF;
-
program the desired transmitter button for the AUX output
(see the relevant paragraph)
The AUX output switches on/off whenever the programmed
transmitter is pressed.
13.1 - SELECTION OF AUX OUTPUT
Default setting = AUX disabled
This procedure allows activating the "AUX" output. By default,
the AUX output is bistable and is associated with the remote
control key memorized for this function.
m
To control the AUX output you need to register a radio
transmitter by following the procedure described in the
relevant paragraph and connect a suitable relay.
1. PRESS THE START BUTTON FOR 3 SECONDS All the LEDs turn
off (if not, refer to Paragraph 15)
2. PRESS THE RADIO BUTTON FOR 1 SECOND: if the "Sic" LED is
off, the AUX output is disabled (if the setting is correct, go to
point 5, if not, go to point 3)
3. PRESS THE SET BUTTON FOR 1 SECOND:
•
if the "Sic" LED is lit red, the AUX output is set on the
Phototest terminals (4 and 8) (if the setting is correct, go
to point 5; otherwise, proceed to point 4)
OR
•
if the "Sic" LED is green, the AUX output is set on the
Flash terminals (1 and 2) (if the setting is correct, go to
point 5; otherwise, proceed to point 4)
4. PRESS THE SET BUTTON AGAIN FOR 1 SECOND: the "Sic" LED
lights up according to the selected setting
5. Press the SET and RADIO buttons at the same time or wait 10
seconds to exit the procedure: the LEDs return to the normal
operating configuration
Publicidad
