Hints For The Operator - Nussbaum WA 950 Instrucciones De Uso

1. Important Information to CURA S 9xx
Dear Customer,
The Wheel Aligner WA 950 / WA 970 differs from the one
described in this manual in the following points:
1. Ergonomically designed sensor head casing with a big
handle.
2. Power button instead of power switch on the sensor
heads.
3. Elektronic bubble level in five instead of three steps on
the sensor head.
4. Quicker data transfer protocol: In the password pro-
tected setup, you have to select sensor head type
‚Cable Sensors 2008' or ‚Radio Sensors 2008'. If you
do not get the Aligner model WA 950 / WA 970
correctly displayed at the start screen of the Alignment
program, this setting is done incorrectly. Data commu-
nication will not work.
5. The internal electrical setup of the machine is simpler.
Instead of a triple DC power supply board with three
LEDs as described, there is only one single 12V DC
switching power supply for everything. Instead of the
thick, red sensor canbles, there are thinner, but more
robust black sensor cables with a plug that is molded
on.
6. Radio Aligners WA 970: Data transmission is done with
a similar black transceiver box that is plugged in on top
of the cabinet.
But this one is working in the 2.4GHz range (instead of
the 433MHz used up to now). If needed, you can select
a different channel with a small service program that is
called from the password protected setup area.
The batteries are the same as in the WA 920 aligners.
These are off-the-shelf 7.2V 3000mAh NiMH batteries
in ‚Racepack' form.
The big difference is that the intelligent charge control-
ler is no longer inside the cabinet, but inside each
sensor head.
The batteries will even charge when the sensor head is
connected via cables during a measurement.
The new machines are explicitly identical with the existing
range concerning these points:
- Software protection system with smartcard reader and
SIM/Smartcards used are. Measurement process, run-
out compensation, vehicle selection, datenbank,...
- Same Software Installation is being used, only correct
selection of sensor type in setup required- Identical
alignment accessories (e.g. wheel clamps, turntables,
unlocking smartcards,...)
- Same after sales tools are being used (e.g. calibration
rig)
- Many identical spare parts (mechanical parts, toe caa-
meras, batteries,...)
1 689 979 873N 19.03.2010
1.1

Hints for the operator

The operation and maintenance instructions in this manual are
supposed to tell the user about the correct and safe use of the
machine.
In order to keep the proven-in-use Nussbaum quality concerning
live cycle and performance for this product, you have to follow the
given instruction carefully.
The owner is responsible for the safe environment of the test
equipment.
Use according to specification
Not to follow the operation and safty hints can cause severe
injuries for the operator and people standing by. The machine
may only be operated after having read and understood all
safety hints given in this manual.
To use this machine is only permitted to trained personnel. This
personnel has to be trained with all user and maintenance
manuals and has got to have a proper education and has to
know about the safty standards.
It is necessary:
- to have read and understood the manuals
- to know about properties and performance of the machine
- to keep unauthorised personnel away from the machine
- to check installation and positioning of the machine according
to the standards
- ensure that all operating personnel is trained for correct and
safe operation of the machine
- that power supply is interuppted before all work on electric lines
and electric motors
- to keep this manual in reach and to consult it when ever
necessary.
Do not use this equipment for purposes it is not designed
for!
Operating conditions
– Temperature range : –20 ... +40 ºC
(reduced measuring accuracy)
– Temperature range for precise measurement:
0 ... +40°C
All stickers giving caution and safety hints are never allowed to be
destroyed or taken of. All missing stickers have to be replaced
immediately. Missing stickers can be ordered from your Nuss-
baum distributor
- During operation and maintenance you have to follow the
accident protection guidlines for electrical systems
- when ever you change the setup or construction of the machine
by your own, the manufacturer is no longer responsible for
damage and accidents happening to the machine and all
personnel operating it
57