Publicidad
Idiomas disponibles
Idiomas disponibles
2. Dismantle the paper filter insert and the foam
pre-filter. Make sure that no dirt gets into the
carburettor. Clean the air filter housing.
3. Wash the pre-filter in liquid detergent and wa-
ter. Squeeze dry. Pour a little oil on the filter and
squeeze in the oil.
4. Clean the paper filter insert as follows: Knock it
lightly against a flat surface. If the filter is very
dirty, change it.
5. Assemble in the reverse order.
Petroleum-based solvents such as kerosene may
not be used for cleaning the paper filter insert.
These solvents can destroy the filter.
Do not use compressed air for cleaning the pa-
per filter insert. The paper filter insert must not
be oiled.
5.10.2 Air filter (180 HD)
The pre-filter (foam filter) must be cleaned/re-
placed after 25 hours of operation.
The air filter (paper filter) must be cleaned/re-
placed after 100 hours of operation.
NOTE! The filters should be cleaned/replaced
more often if the machine operates on dusty
ground.
Remove/install the air filters as follows.
1. Remove the protective cover of the air filter
(14:A).
2. Dismantle the paper filter insert (14:B) and the
foam pre-filter (14:C). Make sure that no dirt
gets into the carburettor. Clean the air filter
housing.
3. Clean the paper filter by tapping it gently
against a flat surface. If the filter is very dirty,
replace it.
4. Clean the pre-filter. If the filter is very dirty, re-
place it.
5. Assemble in the reverse order.
Compressed air or petroleum-based solvents such
as kerosene may not be used for cleaning the paper
filter insert. This will damage the filter.
5.11 SPARK PLUG
The spark plug(s) must be replaced every 200
hours of operation (=at every other basic service).
Before disconnecting the spark plug, clean around
its mounting.
Spark plug: Champion RC12YC or equivalent.
Electrode distance: 0.75 mm.
5.12 AIR INTAKE
See 11-12:W. The engine is air-cooled. A blocked
cooling system can damage the engine. Clean the
engine's air intake after 50 hours of operation.
More meticulous cleaning of the cooling system is
carried out during each basic service.
All manuals and user guides at all-guides.com
ENGLISH
5.13 LUBRICATION
All lubrication points in accordance with the table
below must be lubricated every 50 hours of opera-
tion as well as after every wash.
Object
Centre point 4 grease nipples.
Steering
chains
Tensioning
arms
Control
cables
5.14 FUSES
If any of the faults listed below occurs, replace the
relevant fuse. See fig. 26.
Fault
The engine does not start or starts and
stops immediately. The battery is
charged.
Electrical cutting height adjustment
do not work.
All electrical functions are out of
operation. The battery is charged.
6 PATENT - DESIGN REGISTRA-
This machine or parts thereof is covered by the fol-
lowing patent and design registration:
SE9901091-0, SE9901730-3, SE9401745-6,
US595 7497, FR772384, DE69520215.4,
GB772384, SE0301072-5, SE04/000239 (PCT),
SE0401554-1, SE0501599-5.
GGP reserves the right to make alterations to the
product without prior notification.
Action
Use a grease gun filled with
universal grease. Pump until
the grease emerges.
Brush the chains clean with a
wire brush.
Lubricate with universal
chain spray.
Lubricate the bearing points
with an oil can when each
control is activated.
Ideally carried out by two
people.
Lubricate the cable ends with
an oil can when each control
is activated.
Must be carried out by two
people.
TION
EN
Fig.
17
-
18
19
Fuse
10 A
20 A
30 A
61
Publicidad
