Roland XP-30 Manual Del Usuario página 189

General Purpose Controller 6 (Controller number 81)
status 2nd byte
BnH 51H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
General Purpose Controller 7 (Controller number 82)
status 2nd byte
BnH 52H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
General Purpose Controller 8 (Controller number 83)
status 2nd byte
BnH 53H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=control value: 00H - 40H - 7FH (-128 - 0 - +126)
Portamento Control (Controller number 84)
status 2nd byte
BnH 54H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
kk=source note number: 00H - 7FH (0 - 127)
Effect 1 (Reverb Send Level) (Controller number 91)
status 2nd byte
BnH 5BH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
vv=Reverb Send Level: 00H - 7FH (0 - 127)
Effect 3 (Chorus Send Level) (Controller number 93)
status 2nd byte
BnH 5DH
n=MIDI channel: 0H - FH (ch.1 - ch.16)
vv=Chorus Send Level: 00H - 7FH (0 - 127)
RPN MSB/LSB (Controller number 100,101)
status 2nd byte
BnH 65H
BnH 64H
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
mm=MSB of the parameter number specified by RPN
ll=LSB of the parameter number specified by RPN
This device transmits the following RPNs.
RPN Data entry
MSB LSB MSB LSB
00H 00H mmH -
00H 01H mmH llH
00H 02H mmH -
Program Change
status 2nd byte
CnH ppH
n=MIDI channel: 0H - FH (ch.1 - ch.16)
pp=Program number: 00H - 7FH (prog.1 - prog.128)
* This message is not transmitted when the Program parameter (SYSTEM/MIDI/
TRANSMIT MIDI) is OFF.
Channel Aftertouch
status 2nd byte
DnH vvH
n=MIDI channel: 0H - FH (ch.1 - ch.16)
vv=Channel Aftertouch: 00H - 7FH (1 - 128)
3rd byte
vvH
3rd byte
vvH
3rd byte
vvH
3rd byte
kkH
3rd byte
vvH
3rd byte
vvH
3rd byte
mmH
llH
Notes
Pitch Bend Sensitivity
mm : 00H - 0CH (0 - 12 semitones)
ll : 00H
Master Fine Tuning
mm, ll : 20 00H - 40 00H - 60 00H
( -8192 x 50 / 8192 - 0 - +8192 x 50 / 8192 cent )
Master Coarse Tuning
mm : 10H - 40H - 70H (-48 - 0 - +48 semitones)
ll : 00H
Pitch Bend Change
status 2nd byte
EnH llH
n=MIDI channel number: 0H - FH (ch.1 - ch.16)
mm,ll=Pitch Bend value: 00 00H - 40 00H - 7F 7FH (-8192 - 0 - +8191)
System Realtime Messages
Active Sensing
status
FEH
* Transmitted at intervals of approximately 250ms.
* Not transmitted if the Active Sensing parameter (SYSTEM/MIDI/TRANSMIT MIDI) is
OFF.
System Exclusive Messages
There is a kind of the Universal Non-realtime messages and the Data Set (DT1) messages in
the System Exclusive messages transmitted by this device.
Universal Non-realtime System Exclusive Messages
Identity Reply Message
When Identity Request message (p. 186) is received, this message will be transmitted.
status data byte
F0H 7EH, dev, 06H, 02H, 41H, 6AH, 00H,
04H, 00H, 00H, 01H, 00H, 00H
Byte Remarks
F0H Exclusive status
7EH ID number
dev device ID
06H sub ID#1
02H sub ID#2
41H ID number
6AH 00H Device family code
04H 00H Device family number code
00H 01H 00H 00H Software revision level
F7H EOX
Data Transmission
Data Set1 DT1
status data byte
F0H 41H, dev, 6AH, 12H, aaH, bbH,
ccH, ddH, eeH, ... ffH, sum
Byte Remarks
F0H Exclusive status
41H ID number
dev device ID
6AH model ID
12H command ID
aaH address MSB
bbH address
ccH address
ddH address LSB
eeH data:
: :
ffH data
sum checksum
F7H EOX
* The amount of data transmitted at one time is fixed for the type of data, and the data will
be transmitted with the fixed starting address and size. Refer to the address and size
given in "Mapa de direcciones de los parámetros" (p. 190).
* Large amounts of data must be divided into packets of 128 bytes or less, and transmitted
at intervals of approximately 20 ms.
* For the checksum, refer to (p. 204).
Aplicación MIDI
3rd byte
mmH
status
F7H
(Universal Non-realtime message)
(dev: 10H - 1FH)
(General Information)
(Identity Reply)
(Roland)
(End Of Exclusive)
status
F7H
(Roland)
(dev: 10H - 1FH)
(XP-30)
(DT1)
The actual data to be transmitted. Multi-byte
data is transmitted in the address order.
(End Of Exclusive)
189