Publicidad
Idiomas disponibles
Idiomas disponibles
1
250 ml
Once the descaling solution is poured inside the drawer,
press
to start the main descaling process.
The descaling phases do not need you to stay in front
of the appliance. After each phase is completed, an
acoustical feedback will be played and the display will
show instructions to proceed with the next phase.
Once the descaling phase has been completed, the
boiler will be drained: the descaling solution used
during this phase will be poured into the extractable
drawer.
»
PHASE 2/2: RINSING (30 min.)
To remove descale residuals from the drawer and the
steam circuit, rinse cycle has to be done. When display
shows <ADD 0.25 L OF WATER> fill the tank with 0,25 L
of drinking water, then press
not turn off the oven until all the steps required by the
function have been completed.
When the message "DESCALING COMPLETED" appears
on the display, please press OK to confirm.
Cooking functions cannot be activated during the
cleaning cycle. Please note: A message will be shown
on display, to remind you to execute this operation
regularly. When Descale procedure is completed, it
is suggested to dry the cavity from potential water
residuals. It will be then possible to use all the steam
functions.
Note: during the Descale cycle, some noise could potentially
be heard since the oven pumps are activated in order to
guarantee the optimal descale efficiency.
Once the maintenance cycle has started, do not remove the
drawer unless requested by the appliance
. MINUTEMINDER
When the oven is switched off, the display can be used
as a timer. To activate this function, make sure that the
oven is switched off and press
flash on the display.
Press
or
to set the length of time you require and
then press
to activate the timer.
MINUTE-MINDER
An audible signal will sound and the display will
indicate once the minuteminder has finished counting
down the selected time.
= 75 g
+
2
+
3
to start the rinsing. Do
or
: The
icon will
Please note: The minuteminder does not activate any of the
cooking cycles. Press
or
timer; press
or
to switch the timer off at any time.
Once the minuteminder has been activated, you can
also select and activate a function.
Press
to switch on the oven and then select the
function you require. Once the function has started,
the timer will continue to count down independently
without interfering with the function itself.
Please note: During this phase, it isn't possible to see the
minuteminder (only the
continue counting down in background. To retrieve the
minuteminder screen press
currently active.
. USING THE MEAT PROBE (IF PRESENT)
The meat probe supplied allows to measure the exact
internal temperature of food during cooking.
The meat probe is allowed only in some cooking
function (Conventional, Forced Air, Convention Bake,
Turbo Grill, Slow Cooking and 6
It is very important to position the
probe accurately in order to obtain
perfect cooking results. Insert the
probe fully into the fleshiest part of
the meat, avoiding bones and fatty
parts. For poultry, the probe should
be inserted sideways, in the middle
of the breast, taking care to ensure
the tip does not end up in a hollow
part.
In the case of meat with very irregular thickness, check
it is cooked properly before removing it from the oven.
Connect the end of the probe in the hole located on the
right wall of the oven cavity.
When the meat probe is plugged to the oven cavity, a
buzzer sounds and the display shows icon and target
temperature. If the meat probe is plugged during the
selection of a function, display switches to the default
meat probe target temperature.
Press
to start settings. Use
set the meat probe target temperature. Press
confirm.
Use
and
button to set oven cavity temperature.
Press
or
to confirm and start the cooking cycle.
to change the time set on the
icon will be displayed), that will
to stop the function that is
Sense Meat).
th
and
button to
to
Publicidad
