Publicidad
Idiomas disponibles
Idiomas disponibles
Parts list
Filter pump (7) (fig. G)
Air release valve (7a)
Sealing ring for air release valve (7b)
Filter housing cover holder (7c)
Filter housing cover (7d)
Filter pump cartridge (7e)
Filter housing rubber seal (7f)
Mains cord (7g)
Inlet (7h)
Outlet (7i)
O-ring (7j)
Hose for filter pump (8) (fig. F)
Perforated screen (9) (fig. F)
Clamp (10) (fig. F)
Clamp screw (11) (fig. F)
Plastic stopper (13) (fig. F)
Technical data
Use only this pump for this mini-pool.
Model: 53011A, 12V, 50 Hz, 25 W, Maximum
IPX7
Flow rate: 1200 l/h
Pump power-supply unit:
Stermay HT-53011A-1
IP 65
Plug IP 44
Primary: 230-240V ~ 50 Hz
Secondary: 12V ~, 3000mA, 36VA, 0.83PF
= Protection Level II
Manufacturer: DongGuan Huatao Metal&Plastic
Products Co., Ltd.
No. 2 Yan He Road, Xia Bian Avenue, Chang
An Town, DongGuan City, GuangDong Province
Importer: DELTA-SPORT Handelskontor GmbH
Wragekamp 6, 22397 Hamburg
Germany
Intended use
The filter pump serves to keep the water clean
and may be connected only to those mini-pools
for which it is intended. The mini-pool and the
filter pump have been developed for private use
in the leisure sector.
Safety instructions
• This product can be used by
children above the age of 8
and by people with reduced
physical, sensory, or mental
capacities or by those lacking
experience and knowledge
provided they are supervised
or have been instructed in the
safe use of the product and
understand the risks involved.
Children may not play with
the product. Cleaning and
user maintenance may not be
performed by children without
supervision.
• WARNING. Use only the 53011A pump
included in delivery and supplied by the man-
ufacturer: DongGuan Huatao Metal&Plastic
Products Co., Ltd.
• WARNING. Inspect all clamps and accesso-
ries before starting the pump.
• WARNING. Do not bury the power supply
cord. Place the power supply cord where it
cannot be damaged by lawnmowers, hedge
trimmers or other devices.
• WARNING. Do not use the filter pump to
empty the pool. The pump may be used only
on an erectable pool, not on one that has
been sunk into the ground.
• WARNING. Power supply cord and input
cable are not interchangeable. Should the
power supply cord or the input cable become
damaged, the power supply unit or pump
must be disposed of.
• WARNING. Pump and adapter may not be
installed at locations where they may be sub-
ject to flooding or where there is no suitable
power outlet available.
• WARNING. Make sure that the external
power outlet is protected with a residual-cur-
rent-operated circuit breaker (FI/RCD) with a
maximum trip current of 30 mA.
• WARNING. The filter pump must be at-
tached to a stable base with screws before it
is switched on.
• WARNING. Take care that the filter pump
motor does not overheat. Ensure that the
pump is always full of water so that it does not
operate when empty. Incorrect use can lead
to overheating and subsequent damage due
to the motor burning out.
• WARNING. If air remains in the system,
this makes the pump work faster and leads to
damage. Switch the filter pump off and open
the air release valve (2a) slightly to allow all
air to escape from the hose and from the filter
pump.
• WARNING. The pump must be supplied via
a residual-current-operated protective device
with a rated differential current of not more
than 30 mA.
• WARNING. The power-supply unit should
be installed at least 2m away from the
mini-pool. The mains plug should be located
3.5m away from the pool.
• WARNING. The pump should be firmly
anchored to the ground to prevent it from
possibly tipping over. Ask a specialist retailer
regarding what screws or bolts to use.
Risk of electrical shock!
Defective electrical installation or too high a
mains current can lead to electrical shocks.
Connect the pump only to an easily accessible
power plug so that you can quickly disconnect it
from the mains supply in case of a failure.
• Connect the pump only to a correctly installed
shock-proof socket and then only if the supply
voltage of the socket matches the information
on the product label.
• The pump may not be used when people are
in the water.
• Do not operate the pump if it shows visible
signs of damage or if the mains cord and/or
power plug is defective.
• If the mains cord to the pump is damaged, the
pump must be disposed of.
• Do not open the housing. Entrust repairs to
professionals. Contact a specialist workshop.
In the event of repairs being made inde-
pendently (by the owner or by a third party)
improper connections, or incorrect operation,
liability and warranty claims are excluded.
• Only parts matching the original equipment
data can be used in repairs.
• This pump contains electrical and mechanical
parts that are indispensable to protect against
potential hazards.
• Do not immerse the pump, mains cord, or
power plug in water or other fluids.
• Never touch the power plug with wet hands.
• Never pull the power plug out of the socket by
the mains cord; always hold the power plug
instead.
• Never use the mains cord to carry the prod-
uct.
• Keep the pump, power plug, and mains cord
away from open flame and hot surfaces.
• Place the mains cord so that no one can trip
over it.
Connecting the filter pump
1. Assemble the mini-pool completely and fill it
with water.
2. Remove all parts of the filter pump (7) and
hoses (8) from the packaging.
3. Set up the filter pump so that it stands 20cm
to 1m below the water level.
Note: The filter pump must be mounted on an
even and stable base. On the bottom of the filter
pump there are drill holes for appropriate assem-
bly materials (not included in delivery).
4. Place the filter pump cartridge (7e) in the fil-
ter housing (7) (fig. G). Ensure that the filter
cassette is located fully in the filter housing.
5. Place the filter housing rubber seal (7f) on
the filter housing (fig. G).
6. Place the filter housing cover (7d) on the
filter housing (fig. G).
7. Tighten the filter housing cover by turning
clockwise.
GB/IE
29
Publicidad
