Crivit 388673 2107 Instrucciones De Uso página 28

8. Connect the first hose of the filter pump (8)
to the inlet (7h) of the filter pump with
the aid of the clamp (10) and the clamp
screw (11) (fig. F).
9. Connect the other end of the hose to the mi-
ni-pool's lower hose connection (1c) (fig. F).
10. Turn the air release valve (7a) slowly one to
two rotations anticlockwise.
11. Connect the second hose to the mini-pool's
upper hose connection (1c) and to the
outlet (7i) of the filter pump.
Operating the filter pump
1. Make sure that the mini-pool is completely full
of water and that the filter pump (7) has been
set up at a suitable location.
2. Remove the plastic stopper (13) from the filter
pump valve (1c) on the inside of the swimming
pool (fig. F).
3. When water flows into the filter pump,
trapped air is able to escape via the air
release valve (7a).
4. Then close the air release valve slowly by
turning clockwise.
5. Connect the mains cord (7g) to a suitable
power outlet and let the filter pump run until
the water is sufficiently clean.
Repairs, maintenance
Before each maintenance disconnect the power
supply from the filter pump (7).
Do not place the filter pump in tall grass as this
may lead to overheating.
Should you detect any damage or defects in the
filter pump, take it to a specialist workshop for
repair or else replaceit with a new one. Do not
make any technical modifications to the product.
Do not use solvents to clean the filter pump.
1. Disconnect the mains cord (7g) from the pow-
er supply completely.
2. Detach the filter housing cover (7d) and its
cover holder (7c) by turning it anticlockwise.
3. Clean the filter pump cartridge (7e) and if
need be replace it with a new one.
4. Check the inside of the filter housing (7). If
there are dirt or deposits inside, rinse them out
with clear water.
5. Reassemble all parts and plug in the mains
cord again.
Troubleshooting
1. The filter pump does not work.
• Check for burnt or tripped fuses; check for
loose electrical wiring.
• Inspect the motor. If the motor is overheated
or overloaded, switch the device off. Let the
motor cool down.
• Consult a specialist.
2. The motor runs but little or no water is being
pumped.
• Check for blockages in the inlet or outlet
hose inside the pool walls.
• Tighten the hose clamps, inspect the hose
for damage and check the water level in
the pool.
• Clean the filter cartridge more frequently.
Use a garden hose for this.
• Replace the filter cartridge.
• Consult a specialist.
30 GB/IE
3. The filter pump no longer draws water.
• Make sure that the water level in the pool
with the pump switched off is at least 5cm
above the suction port.
• Make sure that the extraction hose is in
good order and condition.
• Check the filter cartridge for dirt. Clean if
necessary. Use a garden hose for this.
• Consult a specialist.
4. The filter pump is not cleaning the water.
• Set correct chlorine content and pH value.
• Replace or clean the filter cartridge. Use a
garden hose for this.
• Check the filter cartridge for damage and
replace if necessary.
• Run the pump for a good while.
• Remove dirt from the screens in the pool
wall.
• Consult a specialist.
Disposal
In the interest of protecting the environ-
ment, do not throw your product into the
household waste once you are finished
with it, but rather take it to a specialty
disposal facility. Find out about collection sites
and their hours of operation from your local
authority.
Dispose of the product and packaging in
an environmentally friendly
manner.
Note the label on the packaging
materials when separating waste, as
these are labelled with abbreviations (a)
and numbers (b) with the following meaning:
1–7: plastics/20–22: paper and card-
board/80–98: composite materials.
The product and the packaging materials can be
recycled, dispose of them separately for better
treatment of waste. The Triman logo only applies
to France. Find out how to dispose of the used
product from your municipal or city administra-
tion.