Braun Aesculap GN200 Instrucciones De Manejo página 46

fr
TEST INTERVAL:
TYPE OF DEVICE:
MANUFACTURED BY:
SN: ............................... INVENTORY NO.:
Measurement
equipment: ...........................................................................................................................................................................................
S C O E P O F N I S E P T C O I N
1.) VISUAL INSPECTION
1.1 Inspection of power cable for visually detectable damage
1.2 Inspection of foot switch for visually detectable damage
1 3 . y T e p p a l e t s l i t p l e r e s t n
1.4 Check fuse links for prescribed values
1.5 Overall condition of device: dirt, damage
2.) ELECTRICAL INSPECTION
Protective earth resistance incl. mains cable
2.1
according IEC62353:2007
Earth leakage current
2.2
according IEC60601-1*
Enclosure leakage current/touch current
2.3
according IEC60601-1*
Patient leakage current
2.4
according IEC60601-1*
Equipment leakage current - alternative method
2.5
according IEC62353:2007
Applied part leakage current - alternative method
2.6
according IEC62353:2007
2.7 HF-leakage current bipolar
according IEC60601-2-2:2009
2.8 Insulation resistance
according IEC62353:2007 (Preparation according Service Manual)
2 8 . 1 . M i a s n a a g n i t s H
2 8 . 2 . M i a s n a a g n i t s h
2 8 . 3 . H - F u o p t t u a a g n i
2.9 HF-output power measurement with induction-free resistor
Instrument
C 5
C24/44
2.10 DC resistance between the two HF output poles
according IEC60601-2-2:2009 section 201.8.4.102
2.11
Function test according to instructions for use
E T T S R S E U T L
Deficiencies were determined, by which patient, user or other individuals can be endangered
Repair
P a l e c D / a e t
* The listed allowable values comply with the requirements of the IEC60601-1:1988+A1:1991+A2:1995 and IEC60601-1:2005
Fig. 13 Procès-verbal de contrôle technique de sécurité
44
Inspection protocol – safety inspection
1 Year
Bipolar Electrosurgical Unit GN200
Aesculap AG, Am Aesculap-Platz 78532 Tuttlingen/Germany
RESPONSIBLE
............................... ORGANIZATION: ..........................................................................
a d n e r d a b a e l
F u o p t t u
u o i s g n
t s h u o i s g n
Channel R
Load
Ω
1 0 5
50 Ω
1
Ω
2 0 5
..............................................................
I s n e p t c r o S / g i a n u t e r
PASS
Measured value
= 0,3 Ω (at
R 0,2 A)
≥
max
N.C. I = 0,50 A
m
max
S.F.C. I = 1,00 A
m
max
N.C. I = 0,10 A
m
max
S.F.C. I = 0,50 A
m
max
N.C. I = 0,01 A
m
max
S.F.C. I = 0,05 A
m
max
I = 1,00 A
m
max
I = 0,05 A
m
max
I = 122 A
m
max
test voltage = 500 V DC
R = 7 MΩ
min
R = 2 MΩ
min
R = 2 MΩ
min
Rated value
145 Watt ± 20 %
150 Watt ± 20 %
150 Watt ± 20 %
R = 2 MΩ
min
Performed:
No
Next date of inspection
Responsible Organization
V r e i d t c
FAIL
Verdict
Pass / Fail
Yes