Gardena 6300 SilentComfort Instrucciones De Empleo página 9

4. Select 6 to navigate between the times for the max. runtime or
l) When working on slopes, always be sure of your footing, always work
deactivate it with OFF.
across the face of slopes, never up or down and exercise extreme cau-
5. Confirm with 2 to set the max. runtime. tion when changing direction. This reduces the risk of loss of control, slipping
and falling which may result in personal injury.
The screen displays Saved.
m) Use extreme caution when reversing or pulling the lawnmower
Your pump stops after the selected max. runtime.
towards you. Always be aware of your surroundings.
This reduces the risk of tripping during operation.
n) Do not touch blades and other hazardous moving parts while they are
12. Factory reset
still in motion. This reduces the risk of injury from moving parts.
o) When clearing jammed material or cleaning the lawnmower, make
sure all power switches are off and the battery pack is disconnected.
To reset all your settings:
Unexpected operation of the lawnmower may result in serious personal injury.
p) When clearing jammed material or cleaning the lawnmower, make
1. Open the settings 3 and navigate to Factory reset.
sure all power switches are off and remove the safety key.
Unexpected operation of the lawnmower may result in serious personal injury.
2. Select 2 to open the menu.
Stop the cutting means if the machine has to be tilted for transportation, when
The Factory settings menu opens
crossing surfaces other than grass and when transporting the machine to and
3. Select 2 to reset all your settings.
from the area to be used.
Do not tilt the machine when switching on the motor, except if the machine has to
The screen shows Success and the pump restarts.
be tilted for starting. In this case, do not tilt it more than absolutely necessary and
This process may take some time.
lift only the part which is away from the operator.
Stop the machine, remove the safety key and remove the battery, and make sure
v Do not disconnect the garden pump from the mains.
that all moving parts have come to a complete stop:
v To restart your garden pump, follow the instructions in chapter 3. Initial
– After striking a foreign object, inspect the machine for damage and make
start.
repairs before restarting and operating the machine.
4. Remove the garden pump from the Bluetooth – If the machine starts to vibrate abnormally, immediately inspect for damage,
replace or repair any damaged parts and check for and tighten any loose parts.
device.
Maintain the mower at regular intervals.
This will extend the working life of the mower.
13. Troubleshooting
Only use spare parts recommended by GARDENA.
This is the only way to ensure safe use of the mower.
Be careful during adjustment of the machine to prevent entrapment of the fingers
If the display shows a message, look up the possible cause in the tables
between moving cutting means and fixed parts of the machine.
below and solve the problem.
Always allow the machine to cool down before storing.
When servicing the cutting means be aware that, even though the power source
NOTE:
is switched off, the cutting means can still be moved.
Repairs must only be done by the GARDENA service departments or
We recommend to wear a hearing protection.
specialist dealers approved by GARDENA.
v For any other malfunctions please contact the GARDENA service
1.3 Additional safety warnings
department.
1.3.1 Intended use:
The GARDENA Lawnmower is intended to mow lawn in private domestic
13.1 Errors:
gardens and allotments.
The product is not intended for long term use (professional use).
Error message Possible Cause
Very hot water The water in the pump is
DANGER!
strongly heated. In case of water
Risk of physical injury!
WARNING
leakage and contact, injuries will
v Do not use the product to cut bushes, hedges, shrubs, to cut of
Very hot water
occur.
– D o n o t
climbers or grass on roofs or balcony boxes, to chop up branches,
o p e n – N i c h t ö f f n e n
twigs and to level irregularities in the soil.
v Do not use the product on a slope steeper than 20° maximum.
1.3.2 Safety warnings for batteries and chargers
Read all the safety and general instructions.
Failure to observe the safety and general instructions may result in electric shock,
fire and / or serious injury.
Store these instructions in a safe place.
Only use the charger if you can fully evaluate all functions and carry them out
Frost The ambient temperature is too
without restrictions, or if you have received corresponding instructions.
low: there is a risk of frost.
v Supervise children during use, cleaning and maintenance.
WARNING
This will ensure that children do not play with the charger.
Frost
v Charge only lithium-ion batteries of the POWER FOR ALL system type
PBA 18V with a capacity of 1.5 Ah or more (5 battery cells or more). The
battery voltage must match the battery charging voltage of the charger.
Do not charge any non rechargeable batteries.
Hardware error There is a fault with the hard­
Otherwise there is a risk of fire and explosion.
ware of your pump.
WARNING
v
Do not expose the charger to rain or wet conditions.
Hardware error
Water entering a power tool will increase the risk of electric shock.
v Keep the charger clean. Dirt poses a risk of electric shock.
v Always check the charger, cable and plug before use. Stop using the
Error 0
charger if you discover any damage. Do not open the charger yourself,
and have it repaired only by a qualified specialist using only original
WARNING
replacement parts.
Error 0
Damaged chargers, cables and plugs increase the risk of electric shock.
v Do not operate the charger on an easily ignited surface (e. g. paper,
textiles, etc.) or in a flammable environment.
Error message Possible Cause
There is a risk of fire due to the charger heating up during operation.
Pump does not start The non­return valve is blocked
v In order to avoid safety hazards, if the power supply cord needs to be
or not installed.
replaced, this must be done by GARDENA or by a customer service centre
that is authorised to repair GARDENA power tools.
v Do not operate the product while it is charging.
Products sold in GB only: Your product is fitted with an BS 1363/A approved
electric plug with internal fuse (ASTA approved to BS 1362). If the plug is not
Special case pressure
suitable for your socket outlets, it should be cut off and an appropriate plug fitted
amplification.
in its place by an authorised customer service agent. The replacement plug
should have the same fuse rating as the original plug. The severed plug must be
12 10
14638-20.960.03.indd 12 14638-20.960.03.indd 12
disposed of to avoid a possible shock hazard and should never be inserted into
a mains socket elsewhere.
v These safety warnings apply only for 18V Li-ion rechargeable batteries
for the POWER FOR ALL system.
v Use the rechargeable battery only with products from POWER FOR
If an error has been triggered 3 times within 30 minutes, the pump starts a 5­minute cooling
ALL System partners. 18V rechargeable batteries labelled with POWER FOR
phase.
ALL are fully compatible with the following products: All 18 V products from
v Let your pump cool down for 5 minutes and don't open it.
POWER FOR ALL System partners.
v Observe the battery recommendations in the operating manual of
Error 1
your product.
Only this way can the rechargeable battery and the product be operated without
danger and the rechargeable batteries protected from hazardous overloading.
v Only charge the batteries using chargers recommended by the manu-
facturer or by POWER FOR ALL system partners. A charger that is suitable
for one type of battery pack may pose a fire risk when used with different batter-
Error message
ies (Battery type: PBA 18V... / compatible chargers: AL 18...).
Pump does not suck
v The battery is supplied partially charged.
To ensure full battery capacity, fully charge the battery in the charger before using
your power tool for the first time.
v Keep battery packs out of the reach of children.
v Do not open the battery. There is a risk of short-circuiting.
v In case of damage and improper use of the battery, vapours may be
emitted. The battery can set alight or explode.
Ensure the area is well ventilated and seek medical attention should you experi-
ence any adverse effects. The vapours may irritate the respiratory system.
v If used incorrectly or if the battery is damaged, flammable liquid may
settings of your mobile
®
be ejected from the battery. Contact with this liquid should be avoided. If
contact accidentally occurs, rinse off with water. If the liquid comes into
contact with your eyes, seek additional medical attention.
Liquid ejected from the battery may cause irritation or burns.
v If the battery is damaged liquid can be ejected and cover nearby sur-
faces. Check affected parts. Clean these parts or change them if necessary.
v Do not short-circuit the battery pack. When the battery pack is not in
use, keep it away from other metal objects, like paper clips, coins, keys,
nails, screws or other small metal objects, that can make a connection
from one terminal to another.
Shorting the battery terminals together may cause burns or a fire.
Pump does not start
v The battery contacts can be hot after use. Be careful of the hot con-
tacts when remove the battery.
v The battery can be damaged by pointed objects such as nails or
screwdrivers or by force applied externally. An internal short circuit may
occur, causing the battery to burn, smoke, explode or overheat.
v Never service damaged battery packs. Service of battery packs should
only be performed by the manufacturer or authorised service providers.
v
Remedy
Error 2
v Do not touch any escaping
water. v Only operate and store the battery at an ambient temperature
between – 20 °C and + 50 °C.
v Do not open any closures and
Do not leave the battery in your car in the summer, for example.
screw connections on the
At temperatures of < 0 °C some devices may experience a loss of power.
pump and the connecting
v Only charge the battery at an ambient temperature which is between
devices.
Error message
0 °C and + 45 °C. Only charge the rechargeable battery with a USB cable
v Let your pump cool down.
at an ambient temperature which is between + 10 °C and + 35 °C.
Pump does not suck
v Ensure the water supply on
Charging outside of this temperature range can increase the risk of damage to
the suction side before
the battery and pose a fire hazard.
restarting.
v After use, allow the battery to cool down for at least 30 minutes before
v Fill the pump completely with
charging or storing.
water.
v Open the consumer on the
1.3.3 Additional electrical safety warnings
pressure side.
v Take your pump out of opera­
tion.
This product makes an electromagnetic field while it operates. This field
v Store the pump in a frost­
may under some conditions interfere with active or passive medical
proof place (see operating
implants. To decrease the risk of conditions that can possibly injure or
manual of your pump,
kill, we recommend persons with medical implants to speak with their
5. STORAGE).
physician and the medical implant manufacturer before you operate the
product.
v Disconnect the pump from
Pump does not suck
v Disconnect the battery pack when not in use.
the power supply and contact
v Do not use in explosive environment.
GARDENA Service.
v Remove the battery in the case of emergency.
v Use the safety switch in the case of emergency.
v Only use the battery product between 0 °C to 40 °C.
v Do not operate the product in rain or wet conditions.
v Protect the battery contacts from moisture.
1.3.4 Additional personal safety warnings
Remedy
Pump does not start
v Check the non­return valve
Small parts can be easily swallowed. There is also a risk that the polybag
for ease of movement and
can suffocate toddlers.
contamination (see operating
v Keep toddlers away when you assemble the product.
manual of your pump, 6.3 To
clean the non-return valve). v Do not cut grass by pulling the machine towards you.
v Keep the air inlets clean with a brush before storage.
v With the pump running, first
v Do not reach through openings while using the mower.
open the pressure side, then
v Disabled or weak persons should ask a second person for help with the
the water supply.
transport (weight).
WARNING
Error 1: Coo
Note on Error 1 – 3
WARNING
Error 1
Possible Cause
Pump was not sufficiently filled
with water to be pumped.
Air cannot escape on the
pressure side, because the
pressure side outlets are closed.
The flow sensor is dirty.
The consumer is closed or the
hose is kinked.
The pump housing has heated
up and the thermal circuit
breaker has been activated.
The impeller is blocked.
Protect the battery against heat, e. g. against continuous intense
sunlight, fire, dirt, water and moisture.
There is a risk of explosion and short-circuiting.
WARNING
Error 2
Possible Cause
Problem on the suction side.
DANGER!
Cardiac arrest!
The flow sensor is dirty.
Suction hose deformed or bent. v Use a new suction hose.
The consumer is closed or the
hose is kinked.
DANGER!
The pump housing has heated
Risk of suffocation!
up and the thermal circuit
breaker has been activated.
4:59
l i n g d o w n
Remedy
v Fill the pump and make sure
that water does not drain out
on the pressure side during
the suctioning process (see
operating manual of your
pump, 3. OPERATION).
v Open the pressure side out­
lets (see operating manual of
your pump, 3. OPERATION).
v Clean the flow sensor (see
operating manual of your
pump, 6.3 To clean the
non-return valve).
v Open the consumer.
v Stop the pump by using the
(2)
middle button .
v Remove the kink from the
hose.
1. Let your pump cool down.
2. Open possible shut­off device
in the pressure line (release
pressure).
1. Let your pump cool down.
2. Loosen the impeller (see
operating manual of your
pump, 6.1 To loosen the
impeller).
Remedy
v Immerse the suction hose
end under water.
v Eliminate any leak on the
suction side.
v Clean the check valve on the
suction line and check the
installation direction.
v Clean the suction filter on the
suction hose end.
v Clean the filter lid seal and
turn the lid until the stopper
(see operating manual of your
pump, 4. MAINTENANCE).
v Clean the filter in the pump.
v Clean the flow sensor (see
operating manual of your
pump, 6.3 To clean the
non-return valve).
v Open the consumer.
v Stop the pump by using the
(2)
middle button .
v Remove the kink from the
hose.
1. Let your pump cool down.
2. Open possible shut­off device
in the pressure line (release
pressure).
25.07.22 11:01 25.07.22 11:01