Panasonic EYADA Serie Manual De Instrucciones página 29

CAPACITY AND SPECIFICATIONS
Tool Capacity
EYADA212WA
Model No.
EYADA212WB
Machine screw:
Recommended Work
M2.5 to M4.5
Torque Setting Range 0.3 N ・ m to 2.5 N ・ m
Torque Setting Steps 96 steps
Fastening Torque
±10%
Accuracy*
1200 revolutions per
Speed minute
(10-step adjustment)
<Measurement conditions>
Based on our specified measurement conditions.
* Fastening torque and fastening torque accuracy vary depending on the work status. Be sure to check
them with actual work before use.
* The accuracy of fastening torque is not the accuracy of converted torque.
Tool Specifications
Power Supply Power supplied by power adapter (sold separately) 100 to 240 V AC 50/60 Hz
Motor Brushless motor (30 V DC)
Bit Holder One-touch bit locking mechanism
Applicable bits ( hex shank of 6.35 mm across flats,
Size (Estimated
Overall Length: 271 mm / Grip diameter: Φ38 mm
Dimensions)
Mass (Weight) About 630 g
Trigger Switch Mode Both lever start mode and push start mode available (Switchable on a single
unit)
Wireless
Communication Wireless LAN (IEEE802.11a/b/g/n) *n: HT20 only
Standard*
1
Frequency Band 2.412-2.472 GHz / 5.180-5.240 GHz
Number of channels 2.4 GHz: 1 to 13 channels / 5 GHz: 36, 40, 44, 48 channels
• Fastening OK
Output Signals*
2
• Fastening NG (NOK)
• Count-up
(Count complete)
• Sequence complete
• Forward
Input Signals*
2 Drive permission signal
Operation Panel
7-segment display
(Display)
Operation Button OK button / ▼ button / ▲ button
Notification (Lamp) 4-colour display (Detection lamp)
Notification (Buzzer) 3 steps of volume
56
EN
EYADA218WA EYADA407WA
EYADA218WB EYADA407WB
Machine screw: Machine screw:
M2.5 to M4 M3.5 to M5
0.3 N ・ m to 2.0 N ・ m 1.5 N ・ m to 4.4 N ・ m
1800 revolutions per 650 revolutions per
minute minute
(10-step adjustment) (10-step adjustment)
single-ended 9 mm to 13 mm, double-ended 12 mm to 17.5 mm)
• Reverse • Count quantity
• Serial numbers • Accumulated driving time
• Accumulated quantity, etc.
of tools
• Time • Converted torque
• Rotation time
(Model No. WA only)
• Rotation (times)
• Count method
Settings for Quantity
• Count return
Count
• Count reset
• Ignore judgement time
• Ignore count time
• Batch complete judgement waiting time
• Rotation time upper/lower limit setting
Screw Fastening
• Rotation (times) upper/lower limit setting Converted torque upper/lower
Quality
Determination limit setting (Model No. WA only)
• Soft start
Screw Fastening
• Soft snug
Support
• Disable fastening time
Sequence Control Possible (Setting required on the controller side).
• Collective setting of tools, data management, and simple data analysis is
Others
possible with the Controller Management Software (sold separately)
• Able to run in the "Stand Alone Mode" when not connected to the controller.
• Rotation direction switching (Forward/Reverse)
Common
• Braking ON/OFF setting
Specifications
• Screwdriver cord (2 m)
Included Items
• Screwdriver hanger
• Clutch cover
• Grip attachment (Supplied for EYADA407WA ・ WB only)
• Screwdriver cord (2 m/3 m)
Separately Sold
• Screwdriver hanger
Items
• Clutch cover
• Grip attachment
• Power adapter (with a power cord)
These specifications are subject to change for performance improvement.
*1 About 5 GHz (36, 40, 44, 48 ch) support: The radio equipment supports transmission for indoor
use only, except when it communicates with a base station of 5.2 GHz band high power data
communication system or a land mobile relay station.
*2 Input/output signals on the controller side.
Power Adapter Specifications
Model No.
Input Voltage 100 - 240 V AC, 50/60 Hz 2.6 A
Output Voltage 30 V DC, 3 A
0.16 W (100 V) 0.21 W (240 V)
Standby Power
* When the screwdriver itself is not connected
Mass (Weight) About 590 g
Size (Estimated Overall Length (Long Side) 177 mm × Overall Height (Thickness) 44 mm ×
Dimensions) Overall Width (Short Side) 76 mm
Included Items Power cord 1 m (With grounding plug. Detachable from power adapter itself)
EYSZP001
57
EN