Descargar Imprimir esta página

Stiga PARK Instrucciones De Uso página 48

Ocultar thumbs Ver también para PARK:

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 83
EN
2.4.3 Inhibitor, parking brake (3:A)
The inhibitor locks the "clutch-brake"
pedal in the depressed position. This func-
tion is used to lock the machine on slopes,
during transport, etc., when the engine is
not running.
The parking brake must always be re-
leased during operation.
Locking:
1. Depress the pedal (3:B) fully.
2. Move the inhibitor (3:A) to the right.
3. Release the pedal (3:B).
4. Release the inhibitor (3:A).
Unlocking:
Press and release the pedal (3:B).
2.4.4 Driving-service brake (3:F)
If the machine does not brake as expect-
ed when the pedal is released, the left
pedal (3:B) should be used as an emer-
gency brake.
The pedal (3:F) determines the gearing ratio be-
tween the engine and the drive wheels (= the
speed). When the pedal is released, the service
brake is activated.
1. Press the pedal forward –
the machine moves forward.
2. No load on the pedal – the ma-
chine is stationary.
3. Press the pedal backward –
the machine reverses.
4. Reduce the pressure on the
pedal – the machine brakes.
There is an adjustment plate on the upper section
of the pedal. The adjustment plate can be adjusted
to three (3) positions to suit the driver's foot.
2.4.5 Steering wheel (3:D)
The height of the steering wheel is infinitely ad-
justable. Undo the adjustment knob (3:E) on the
steering column and raise or lower the steering
wheel to the desired position. Tighten.
Do not adjust the steering wheel during
operation.
Never turn the steering wheel when the
machine is stationary with a lowered
implement. There is a risk of abnormal
loads on the servo and steering mecha-
nisms.
48
ENGLISH
2.4.6 Throttle control (4,5:G)
Control for setting the engine's revs.
1. Full throttle – when the machine is in
operation, full throttle should always be
used.
2. Idling.
2.4.7 Headlight (4,5:H)
Pull-type control for turning the headlights on and
off.
2.4.8 Ignition lock (4,5:I)
Ignition lock used for starting/stopping the engine.
There are 3 positions:
1. Stop position – the engine is short-cir-
cuited. The key can be removed.
2. Operating position
3. Start position – the electric start motor
is activated when the key is turned to the
spring-loaded start position. Once the en-
gine has started, let the key return to oper-
ating position 2.
NOTE! If the engine should stop for any reason,
the key cannot be turned directly to position 3
due to a mechanical ignition lock. To start the
engine - turn the key back to position 1 and then
to positions 2 and 3.
2.4.9 Power take-off (4:K)
A lever for engaging and disengaging the power
take-off for operating front-mounted accessories.
Two positions:
1. Lever in forward position – power take-
off disengaged.
2. Lever in backward position - power
take-off engaged.
2.4.10 Hour meter (2:P)
Indicates the number of working hours. Only
works when the engine is running.
2.4.11 Cutting height adjustment (4,5:J)
The machine is equipped with a control for using
the cutting deck with electrical cutting height ad-
justment.
The switch is used to adjust the cutting
height in continuously variable positions.
The cutting deck is connected to the contact (2:Q).

Publicidad

loading