Copying Flight Phases Menu: ( Phases ) Copy; Setting The Transition Speed For Switching Flight Phases Menu; Speed; Further Possible Functions With The Glider Model Type - Multiplex Cockpit SX Manual De Instrucciones

14.10.4. Copying flight phases
) COPY
Menu: ( PHASES
What is copied?
• The current trim settings for AILERON, ELEVATOR
and RUDDER
• Flight phase-specific mixer inputs
Q ->Q aileron input to the outboard flaps
Q ->F aileron input to the inboard flaps
FIX F fixed value for FLAP
mixer inputs for the free mixers
• Flight phase-specific transmitter control settings
Dual-Rate for AILERON, ELEVATOR and
RUDDER
Fixed values for AILERON, ELEVATOR, RUDDER,
which are called up using the FIX button
The source is always the current flight phase, which
you have selected with the PH switch.
The destination for the copy is selected in the menu.
Moving to the KOPIE menu:
to MENU,
(MODEL appears),
to PHASEN,
to KOPIE,
The number 0 flashes in the bottom line. Select phase
1 to 3 as destination using the 3-D digi-adjustor.
Check once more that you have selected the correct
source with the PH switch (
A further brief press on the 3-D digi-adjustor triggers
the copy process, and the flashing ceases.
Note: interrupting without making a copy
If you leave 0 as the destination, no copy will be made.
14.10.5. Setting the transition speed for switching
flight phases

) SPEED

PHASES
Menu: (
The SPEED parameter can be adjusted to determine
the speed of the transition from one flight phase to
another.
Four settings are possible:
SPEED Transition
0
immediate
1
fast
2
moderate
3
slow
14.11.2.
14.12.
14.9.1.
14.11.5.
(SETUP appears),
(MODE appears),
,
table in section 14.4.3.).
approx. 1 sec
approx. 2 sec
approx. 3 sec
Operating Instructions
Moving to the SPEED menu:
to MENU, (SETUP appears),
(MODEL appears), (MODE appears),
to PHASEN, ,
to SPEED,
The current setting flashes. Select the desired value
using the 3-D digi-adjustor.
A brief press on the 3-D digi-adjustor concludes the
process. The value is stored.
14.11. Further possible functions with the
GLIDER model type

14.11.1. Combi-Switch

Just like their full-size counterparts, many models -
especially gliders - are only able to fly smooth turns
with co-ordinated use of ailerons and rudder. The
combi-switch combines (couples) ailerons and rudder,
making it easier for modellers to fly accurate turns in
normal flight. For thermal flying and aerobatics the
combi-switch is not generally used.
The combi-switch mixer itself can be switched on and
off at any time using the "CS/A-ROT" switch (switch
position ON).
You can set the following rate in the COMBI menu. The
available range is -200% to 200% in 5% increments.
The prefix determines the direction of following. In most
cases the model's rudder deflects when the aileron
stick is operated, i.e. the aileron function is the "mas-
ter". To achieve this the values must be set with a posi-
tive prefix (+). A following rate of 100% means that full
aileron deflection produces full rudder deflection. A
following rate of 200% means that full rudder deflection
is obtained when the aileron stick is only at half-travel.
Moving to the COMBI menu:
to MENU,
to MIXER,
to COMBI,
The current percentage figure flashes. You can now set
the value within the range -200% to +200% using the
3-D digi-adjustor.
A brief press on the 3-D digi-adjustor concludes the
process. The value is stored.
Page 43
(SETUP appears),
(GAS>S4 appears, e.g.),