Setting The Stick Mode (Which Stick Controls Which Function?) Menu; Setting The Rotor Head Type Menu; Mode - Multiplex Cockpit SX Manual De Instrucciones

Ocultar thumbs Ver también para Cockpit SX:
Tabla de contenido

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

In the bottom line the "0" flashes. Use the 3-D digi-
adjustor to select the memory in which the new model
is to be stored. Memories already containing data are
not offered as you leaf through, i.e. you cannot acci-
dentally overwrite a model.
Press the 3-D digi-adjustor briefly
selected memory. This takes you to the menu for enter-
ing the model name.
Note: interrupting (no new model)
If you accidentally find yourself at this menu point, or
have selected the wrong model type, enter "0" as the
memory, and the input process is interrupted.
A long press on the 3-D digi-adjustor
the process, and returns you to the INFO 1 display.
A further brief press
on the 3-D digi-adjustor activates
input mode. The first character flashes.
The default model name is <HELI>, but this can be
changed to anything you like.
Changing the model name
Use the 3-D digi-adjustor to search for the desired
character. The following characters are available:
0 to 9, :, /, <, -, >, ?, space, A to Z
Press the 3-D digi-adjustor again briefly .
The second character now flashes, and can be se-
lected in the same way.
Repeat this procedure until you have entered all six
characters. Press the 3-D digi-adjustor briefly
the sixth character to complete the name input process.
Note: interrupting the name input process
If the model name has less than six characters, you
can interrupt the process with a long press
D digi-adjustor. This returns you to the INFO 1 display.
The new model is now stored in the memory, and you
are returned to the "NAME" menu. You can move on to
other menus via "EXIT"; alternatively a long press
takes you directly to the INFO 1 display.
16.3.2.
The stick mode determines which transmitter controls
operate the functions ROLL (aileron), PITCH-AXIS
(elevator), YAW (rudder), and COLLECTIVE PITCH.
Four modes are available:
to confirm your
Study the table to locate the stick mode you wish to
use, then set the appropriate mode.
Moving to the "MODE" menu:
also concludes
The current stick mode flashes. Use the 3-D digi-
adjustor to set your preferred mode.
A brief press
process. The value is stored.
16.3.3.
The picture below shows which functions are controlled
by the individual transmitter controls in the HELI model
type.
Teacher button TRAINER
after
on the 3-
AUX 1
16.3.4.
You have already determined the rotor head type for
your model helicopter In section 16.2.1., but it has not
yet been entered in the transmitter. The head type
must now be set for the current model memory.
Page 61
Operating Instructions
Setting the stick mode
(which stick controls which function?)
SETUP
MODEL
Menu: (
,

Mode

left stick
1
Yaw
Pitch-axis
2
Yaw
Coll. pitch
3
Roll
Pitch-axis
4
Roll
Coll. pitch
to MENU,
(MODEL appears),
on the 3-D digi-adjustor concludes the
Transmitter controls for the HELI type
Switch functions
Auto-rotation A-ROT
Dual-Rate D-R
Slider functions
Setting the rotor head type
MIXER
KOPF
Menu: (
,
) MODE
right stick
Roll
Coll. pitch
Roll
Pitch-axis
Yaw
Coll. pitch
Yaw
Pitch-axis
(SETUP appears),
(MODE appears),
Emergency throttle OFF
THR-CUT
Direct Throttle DTC
Switching flight
phases 1 - 3
PH (
16.10.)
Throttle limiter
THR-LIMIT
) TYP

Publicidad

Tabla de contenido
loading

Tabla de contenido