Kärcher HD 9/100 De Skid *EU Manual Del Usuario página 20

página de 232

/ 232
Marcadores

Idiomas disponibles

18. Start up the device and let the engine warm up for

5 minutes, then check for oil leaks.

19. Shut down the engine.

20. Wait 10 minutes.

21. Check the oil level

22. Correct the oil level if necessary.

Cleaning the air filter element

1. Turn the key-operated switch to position "0".

2. Release the locking elements.

Illustration T

Filter element

Locking element

Cover of the air filter casing

3. Remove the cover of the air filter casing.

4. Remove the filter element.

5. Blow compressed air through the filter element from

the inside (2.9...4.9 bar).

Note: Start with the lowest pressure. Only increase

the pressure if the cleaning effect is insufficient.

6. Wipe the inside of the air filter casing.

7. Replace the filter element if one of the following con-

ditions is fulfilled:

a The engine performance decreases.

b The filter element is heavily contaminated.

c The filter element is fouled with oil.

8. Insert the filter element into the air filter casing.

9. Place the cover on the air filter casing. When doing

this, align the arrows on the cover and the casing.

The device does not run

Device does not reach required pres-

sure

Leak at the high-pressure hose

The high-pressure pump knocks

Internal combustion engine

Engine type

Type

Engine capacity

Cylinder

Power

Specific consumption

Engine speed

Exhaust emissions standard

Battery

Working voltage of the battery

Battery capacity

Length x width x height

Water connection

Feed pressure

Input temperature (max.)

Input amount (min.)

Minimum water supply hose length

Minimum water supply hose diameter

Device performance data

Nozzle size of standard nozzle

Operating pressure

Operating pressure (max.)

Water flow rate

High-pressure gun recoil force

Permissible temperature range

10. The locking elements engage in place.

Replacing the air filter insert

1. Follow the same procedure used for "Cleaning the

air filter element".

2. Replace the filter element with a new filter element

instead of cleaning it.

Troubleshooting guide

Have all checks and work on electrical parts performed

by an expert.

In case of any malfunctions not mentioned in this chap-

ter, contact the authorised Customer Service.

DANGER

The device can start unintentionally.

The high-pressure water jet or impelled parts can cause

injuries.

Set the power switch to 0/OFF and actuate the trigger of

the high-pressure gun until the device is depressurised

before eliminating a malfunction.

The water shortage indicator lamp lights up

1. Check the water inlet pressure and the water vol-

ume.

2. Check the water filter for contamination.

3. In the Advanced version, check the float valves in

the float container.

4. In the Advanced version, check the V-belt of the ad-

vance pressure pump for:

a Condition

Faults that are not displayed

1. Check the indicator lamps.

2. Check the condition of the battery.

1. Check the size of the nozzle.

2. Clean the nozzle and replace if necessary.

3. Replace the filter insert.

a Unscrew the filter casing.

b Renew the filter insert.

c Close the filter casing.

4. Vent the device (see chapter "Venting the device").

5. Check the water supply line to the pump for leaks or blockages.

6. Contact Customer Service if necessary.

1. Turn the trigger to "0/OFF".

2. Discharge the pressure by opening the high-pressure gun.

3. Re-tighten the hose screw connections.

4. Replace the O-rings.

5. If the hose leaks (at the hose surface, at the pressure relief hole) then stop using the high-pressure hose immediately and do

not use it again.

1. Check the water supply line to the pump for leaks or blockages.

2. Vent the device (see chapter "Venting the device").

Technical data

kW/PS

l/h

1/min

MPa

°C

l/min

MPa

l/min

°C

Indicator lamps

HD 9/100 De Skid

*KAP

*EU

Yanmar 4TNV88

Diesel, 4-stroke

2,190

35,5 / 48,2

~9,5

3100

Stage 3a

Stage 5

353x175x190

0,1-0,5

22,5

7,5

1,00 (type F19)

100

110

14,6

122

+5...+40

English

b Belt tension

The low fuel indicator lamp lights up

1. Check the filling level of the fuel tank.

The "charge battery" indicator lamp lights up

1. Check the V-belt of the engine for:

a Condition

b Belt tension

2. Check the condition of the battery.

3. Have the generator checked by the Yanmar service

team.

Engine malfunctions shown in the display

Only EU version devices are equipped with a display.

Current error message

A current error message is shown immediately in the

display.

1. An error message containing further information

about the fault can be called up by pressing the

CONFIRM button.

List of error messages

The error messages that have occurred can be dis-

played by using the "Fault Codes" function.

1. Press the MAIN MENU button.

2. Select the submenu "Fault Codes" by pressing the

NEXT button.

The list of error messages is displayed.

3. Use the DOWN and UP buttons to select an error

message.

4. Use the "?" button to call up detailed information

about this error message.