The Royalevo As Pupil Transmitter; Sub-Menu: User; Parameter: Language; Parameter: Name - Multiplex ROYALevo 7 Manual De Instrucciones

ROYAL evo 7
!
Take care when assigning the throttle or collec-
tive pitch control functions, as the motor could
burst into life! Injury hazard!
Ensure that nobody is in danger of injury if a motor
revs up or bursts into life, and that the model is not
able to cause other damage. For safety reasons the
assignment should be made with the motor
stopped or the electric motor disconnected. You
can check that the system is working as required
by using the servo monitor facility even with the
model switched off (
An assignment can be erased by selecting the control
function and selecting "OFF" using the (
or one of the digi-adjustors.
If the transmitter is switched off in "TeacherU" or
"TeacherM" mode, the transmitter will automatically
switch to the Setup / Training menu when next
switched on, and remind you that the transmitter is op-
erating in this mode.
13.4.3.

The ROYALevo as pupil transmitter

Important: if the ROYALevo is used as a pupil transmit-
ter, the trims have no effect (teacher's trims active).
The following can be used as Teacher transmitters:
ROYALevo 7 / 9 / 12, Commander mc, PROFI mc 3010 /
3030 / 4000.
Some older MULTIPLEX transmitters are also suitable for
use as teacher transmitters. If your teacher transmitter is
not listed above, please enquire at our Customer Ser-
vice Department.
1. Connect the pupil transmitter to the teacher
transmitter using the Trainer lead, # 8 5121, con-
nected to the multi-function sockets. Take care to
connect the cable correctly: the pupil end of the
lead is marked "Schüler" (pupil), the teacher end
"Lehrer" (teacher).
2. Now switch on the teacher transmitter.
The pupil transmitter (ROYALevo7) is automati-
cally switched on, and draws power from the
teacher transmitter.
3. Switch to the Training sub-menu.
4. Select:
Mode = Pupil M, if the teacher transmitter expects
signals in the MULTIPLEX format.
(Neutral pulse width = 1.6 ms)
(e.g. ROYALevo 7 / 9 / 12 with "Teacher M", Com-
mander mc, PROFI mc 3010 / 3030 / 4000).
Mode = Pupil U, if the teacher transmitter expects
signals in the UNIVERSAL format.
(Neutral pulse width = 1.5 ms)
(e.g. ROYALevo 7 / 9 / 12 with "Teacher U")
The following display now appears:
16.3.) .
/ ) buttons
Note:
If the ROYALevo7 is switched off again after a training
session without the Training / Mode parameter be-
ing set to OFF, for safety reasons the transmitter
switches directly to the SETUP / Training menu
when next switched on.
Before every flight in Trainer mode be sure to check
the following points one last time:
Are all the control functions which the pupil is not
permitted to control set to "OFF"?
Is the assignment of the control functions unam-
biguous? It is not permissible for any of the pupil's
servo channels to be assigned twice!
Are all the directions of rotation of the control func-
tions correct? Please check this every time before you
fly the model.
Note:
If the cable connection between the two transmitters is
disconnected during a Trainer session, all control func-
tions automatically revert to the teacher's transmitter.

Sub-menu: User

13.5.

Parameter: Language

13.5.1.
global effect
The ROYALevo7 features two language sets for the
screen texts. By default English (main language) and
German are installed (language set: EN/DE). In the L,
User menu you can switch between these two lan-
guages using the Language parameter.
On the Internet we will be making additional language
sets available for downloading; please visit the
download area
http://www.multiplexrc.de/. You can also download the
PC program ROYALevo-DataManager there, which is
required to install these files in your transmitter. To con-
nect the transmitter to your PC you will need the PC in-
terface lead, # 8 5156. (

Parameter: Name

13.5.2.
global effect
In this field you can enter your own name (user name)
of up to 16 characters. The text is entered using the
method described in the section "Text input" (
11.1.3.). Your name then appears in status display 1 (
10.7.). The default name is "MULTIPLEX".
Page 30
of our website
23.).