Free Assignment With Model Helicopters; Special Features When Assigning; Sub-Menu: Monitor; Sub-Menu: Test Run - Multiplex ROYALevo 7 Manual De Instrucciones

16.2.2.

Free assignment with model helicopters

If you have set up a model helicopter based on one of
the model templates HELImech or HELIccpm, various
transmitter controls can be selected for the free or vari-
able channels. You can find out which channels are free
or variable by consulting the descriptions of the heli-
copter model templates (
Available
Note
controls
Pitch-axis signal only no mixing
Pitch-ax
Yaw signal only
Yaw
Throttle signal, plus mixed throttle curve,
throttle limiter, direct throttle, EMERGENCY
Throttle
throttle CUT
Spoiler signal only
Spoiler
Control signal for speed controller
RPM
Retract signal
L. gear
Aero-tow signal
Aero-tow
Brake signal
Brake
Gyro signal, including all mixed signals
Gyro
from the Gyro mixer
Mixture signal only
Mixture
AUX1
AUX1/2 signal only
AUX2
Coll. pitch signal only no mixing
Coll. P.
16.2.3.

Special features when assigning

The transmission mode PPM 6 or PPM 7 is set automati-
cally:
Last servo on channel 6 PPM 6
Last servo on channel 7 PPM 7
Problems may occur with PPM 6 and certain older types
of speed controller, in which case it may help to assign
any function to channel 7. This forces PPM 7 operation;
you do not need to connect a servo to the output.

16.3. Sub-menu: Monitor

The Servo Monitor is a substitute for a receiving system
and servos, enabling you to check the function and op-
eration of servos, speed controllers and - especially -
gyro systems (for which an external effect is not easy to
detect), and seek and eliminate faults.
Call up the menu, then press the ENTER button or a 3D
digi-adjustor; the Servo Monitor then appears.
Two display variants are available:
graphic, with bar-form display of output signals
(Fig. 1), and
numerical, with display of % values (Fig. 2).
You can switch between the two displays using the UP /
DOWN buttons ( / ) or one of the two 3D digi-
adjustors.
20. onward):
no mixing
no mixing
no mixing
mixing
mixing
no mixing
no mixing
ROYAL evo 7 - Instructions
Press the ENTER button or one of the 3D digi-adjustors
to close the Servo Monitor.

16.4. Sub-menu: Test run

Automatic servo run, designed for test and demonstra-
tion purposes or as an "electronic aid" for range-
checking.
As soon as you select a transmitter control, the transmit-
ter generates a constant control signal with variable
transit time, i.e. from one end-point of the control to the
other. All servos which are operated by this transmitter
control, either directly or via a mixer, start running.
You can interrupt the test run by either of two methods:
Press the REV/CLR button
Select no transmitter control (" - - - - - - - ")
The transit time can be set to any value in the range 0.1
– 4.0 seconds.

17.Main Menu Timer A

The ROYALevo7 features a stopwatch with alarm func-
tion which can be used for various timing tasks. The
stopwatch counts up to 4½ hours with a resolution of
one second.
Line 1: Time
This is the time which has elapsed since the timer
started. If you select this field, you can erase the time
using the REV/CLR button.
The stopwatch can also be reset by pressing the
REV/CLR button when you are in one of the status dis-
plays 1 - 3.
Line 2: Alarm
This is where you set the alarm time. For example, if the
motor run of an electric-powered model is four minutes,
you should set 0:04:00 at this point. The timer adds
together the motor run time based on the throttle set-
ting, and emits a warning sound once the set alarm time
has elapsed.
The method of entering the alarm time differs from the
usual procedure: here the value is entered digit by digit:
press the ENTER button or one of the 3D digi-adjustors.
The cursor jumps to the hours, which can then be set
using the UP / DOWN buttons or one of the 3D digi-
adjustors. Every time you press ENTER again, the cursor
moves one place to the right etc.
Page 47
" Control " appears