Publicidad
(EN361). It can be equipped with connectors (EN362). It can be connected to a lanyard (EN354), a tensioner with a support lanyard
(EN358). In these cases, follow the instructions described in their own manual.
recommended to assign each user a belt. or support belt, or support lanyard and or restraint harness with integrated lanyard. This PPE
can only be used by one person at a time. During all these operations, be careful not to twist the straps. In the case of use of a belt
incorporated on a harness: slip the straps of the lower part of the harness in the loops positioned on either side of the belt. Position the
belt on the back, close it with the ventral loops.
Closing and opening of the different types of loops: (see diagrams) The belt should be adjusted to the size of the user: adjust the straps
by sliding them into the loops and openings provided for this purpose. In order not to slip, it should be reasonably tight without compressing
the abdomen. The thigh straps should be adjusted to the size of the user: adjust the straps by sliding them into the loops and openings
provided for this purpose. In order not to slip, they must be reasonably tight without compressing the thighs. Test the comfort and settings
in a safe place to ensure that the sit harness are perfectly adjusted to the size of the user and comfortably accompanies his movements.
When the belt is used in a fall prevention device (retained), it must be connected to an anchor point (minimum resistance: 12 kN (EN795)
and located at the user's waist or above the user, in order to reduce to the minimum the potential of fall. Attach the lanyard (EN354)
using the connectors (EN362) or the tensioner with lanyard (EN358) to the side attachment rings. Adjust the length and tension of the
rope with the tensioner so as to provide a stable working position and limit free movement up to a maximum of 0.6 m. The adjustment is
completed, check that any fall is limited to 0.5 m. During use, the overall system must not be in contact with: cutting elements, sharp
edges and structures of small diameter, oils, harsh chemicals, fire, hot metal, all types of electrical conductors... During operation,
regularly check the closing and adjustment and/ or fastening elements. May provide a protective sheath. For safety reasons and before
each use, check: that the connectors (EN362) are closed and locked / that the operating instructions described for each component of
the system are met / that the general disposition of the work situation reduces the fall risk, the drop height and the pendulum movement
in the case of a fall. / the vertical clearance is sufficient (free space beneath the feet of the user) and no obstacles disrupt the normal
functioning of the fall arrest system. The vertical clearance is the stopping distance H + additional safety distance of 1 m. The distance
H measured from the initial position to the final position (user's balance after the fall arrest). (see table): Provide a safe distance from
the ground and the power lines or areas with an electrical hazard. ■ TECHNICAL CHARACTERISTICS (See reference table) : -Materials:
(PART 4). ! ELARA130: Comments: DONNING AND/ OR ADJUSTMENTS: Special note for the harness equipped at the dorsal
attachment point of an irremovable shock absorber with lanyard. The harness with dorsal attachment point to an irremovable restraint
lanyard (EN358) should not be used as a fall arrest system, but as a restraint. Unfold the harness to put it in the correct direction (A).
Harness: Put the harness over the back, pass the head through the upper part (B). Close the Bavarian sternum strap (C). Pass the lower
part between the legs. Assemble the lower and upper part through the loops (D). see diagrams. A harness should be adjusted to the size
of the user: adjust the straps by sliding them in the loops and openings provided for this purpose, so that the seat strap is in place and
the back plate is located between the shoulder blades, adjust the adjustable buckles. The harness must be strapped as close to the body
as possible, without excess, to allow the user free movement. These settings must be made at once only and before the user is in the
fall risk area. Usage limits: ▪ Before any PPE implementation operation, set up a rescue plan to deal with any emergency that may occur
during the operation.
SHELF LIFE : Textile products or those containing textile elements (harnesses, belts, shock absorbers etc...):
maximum life of 10 years in storage (from date of manufacture), 7 years after the first use. The shelf life is given as an indication. The
following factors can cause it to vary greatly: -Non-compliance with the manufacturer's instructions for transport, storage and use /-
"Aggressive" work environment: marine atmosphere, chemicals, extreme temperatures, sharp edges... /-Particularly intensive use /-
Shock or significant constraint /-Disregard for the product item's history. Warning: these factors can cause damage invisible to the naked
eye.
Warning: certain extreme conditions can shorten the shelf life by a few days.
undergo either: - a review /- destruction. The shelf life is not a substitute for periodic verification (minimum annually) which will assess
the condition of the product. TO FIND YOUR LOCAL ANNUAL REVIEW CENTRE, VISIT WWW.DELTAPLUS.EU. No modification or
addition or repair of the PPE may be made without prior written consent from the manufacturer nor without using their procedures. Do
not use beyond the area of use defined in the instructions for use. The manufacturer cannot be held liable for any direct or indirect
accident after a modification or use other than that provided in this manual. Do not use this equipment beyond its limits. To ensure its
working condition and therefore the safety of the user, the product should be checked systematically: ▪ 1 / visually inspect the following
points: State of the strap or rope: no fraying, no boot cut, no visible damage at seams, no burning and no unusual narrowing. / Condition
of seams and fasteners: no visible damage . / Condition of the metal parts: no wear, no deformation, no corrosion or oxidation. / General
condition: look for any possible damage due to ultraviolet radiation and other climatic conditions /
connectors . / Specific conditions such as humidity, snow, ice, mud, dirt, paint, oil, glue, corrosion, wear of the strap or rope, etc..., can
significantly reduce the operation of the fall arrest device. ▪ 2 / in the following cases: Before and during use / if in doubt / In the case of
contact with chemicals, solvents or fuels that could affect operation. / If it has been subjected to stress during a previous fall. / At least
every twelve months by the manufacturer or a competent organization, mandated by them.
examination should be performed at least every twelve months by the manufacturer or a competent organization, mandated by them.
This very important check is related to the maintenance and efficacy of the PPE and hence the user's safety. A written document
authorising reuse should be obtained during this audit in order to reuse the PPE. This document will clarify that the user's safety is linked
to maintaining the efficiency and resistance of the equipment. Replace the PPE if necessary. In accordance with European regulations,
the identification form must be completed prior to the first use of the product and then updated and kept with the product as well as the
manual by the user. The readability of the product labelling should be checked periodically. ▪ WARNINGS: THE BELT IS NOT A
GRIP BODY DEVICE, ONLY THE HARNESS IS RESERVED FOR THIS FUNCTION (EN361).
STRAP, OR SUPPORT BELT, OR SUPPORT LANYARD AND OR RESTRAINT HARNESS WITH INTEGRATED LANYARD) MUST
NOT BE USED AS A FALL ARREST.
restraint or protection device against falls from a height (EN363). ▪ WARNINGS: The user's safety depends on the continuing efficacy
of the PPE, its strength and the proper understanding of the instructions in this manual. WARNINGS: Any static or dynamic overload may
damage the PPE. ▪ WARNINGS: The weight of the user, including his clothing and equipment must not exceed the maximum weight
indicated on the fall arrest. ▪ maximum nominal load. for sit harness. : 100 kg. It is dangerous to create your own fall arrest system as
each safety function may interfere with another safety function. No modification or addition or repair of the PPE may be made without
prior written consent from the manufacturer without using their procedures. Do not use beyond the scope of use defined in the usage
instructions, nor beyond its limits. The manufacturer cannot be held liable for any direct or indirect accident after a modification or use
other than that provided in this manual. ▪ Temperature of working environment : -20°C / +50°C. Some of these PPE have been tested
with a mass constraint 40% / 50% higher than the standard requirements (at 140 kg / 150 kg) , see product marking.
RECORD CARD :PERIODIC REVIEW of PPE: 1/Reference of the product 2/Company 3/User Name 4/The batch number,/Serial N°
5/Date of production 6/Date of 1st Use 7/Purchase date 8/Date of inspection 9/Comments 10/Date of next inspection 11/Name &
Signature 12/Type Personal protective equipment 13/Belt & work positioning system 14/The record card must be completed by the
user before the product is first used, then regularly updated and kept. To be exclusively used as described in the product user instructions.
15/The frequency of inspections must comply with national regulations and in any case an inspection must be performed at least once a
year. The documentation supplied with each product must be kept indefinitely by the user. Storage/Cleaning instructions: ▪ During
transport and storage: - keep the product in its packaging /-keep the product away from any sharp, abrasive, objects etc... / Keep the
product away from sunlight, heat, flames, hot metal, oil, petroleum products, harsh chemicals, acids, dyes, solvents, sharp edges and
structures of small diameter. Store the equipment dry and clean in its original packing, away from light, cold, heat and humidity and at
ambient temperature. These items can affect the performance of the fall arrest device. SERVICING AND STORAGE:
3
DELTA PLUS GROUP - ZAC La Peyrolière - BP140 - 84405 APT Cedex - France - Tel: +33 (0) 4
90 74 20 33 - Fax: +33 (0) 4 90 74 32 59 - www.deltaplus.eu
Sit harness: position the thigh belts on the back of the thighs, close with the loops.
In case of a fall risk, it is necessary to supplement this system with a collective or personal
■DONNING AND/ OR ADJUSTMENTS:
If in doubt, always remove the product for it to
Correct operation and locking of
▪ PERIODIC REVIEW of PPE: An
THE BELT (OR BELT WITH LEG
UPDATE 15/03/2018
It is
▪ PART 2:
Clean with
Publicidad
