Publicidad
Idiomas disponibles
Idiomas disponibles
ENGLISH
Setup and mounting
Carry out connections TP Standard/KD in the following order:
NOTE!
If a remote control is used (optional – not included in scope of delivery):
X The EMERGENCY OFF switch at the remote control must be unlocked!
1. Attach the "Strain relief" snap hook (2e) of the hose package to the "Strain relief" eye (1h) at the power source.
2. Connect the "Gas" plug (2c) of the hose package to the "Gas" socket (1a) at the power source.
3. Connect the "Welding current –" plug (2b) of the hose package to the "Welding current –" socket (1d) at the power source
and lock it with a turning movement.
4. Connect the "Cooling liquid supply line" plug, blue (2a) of the hose package to the "Cooling liquid supply line" socket, blue
(1b) at the power source.
5. Connect the "Cooling liquid return line" plug, red (2d) of the hose package to the "Cooling liquid supply line" socket, red
(1c) at the power source.
6. Connect the Amphenol plug "Control line" to power source" (5b) to the "Control line" socket (1f) at the power source.
7. Connect the "Control line to welding tongs" plug (5a) to the "Control line" socket (3a) at the welding tongs and screw tight.
8. Connect the "Cold wire" plug (2f) of the hose package to the "Cold wire" socket (5c) at the control line and screw hand-tight.
9. Connect the "Ground cable" plug (6b) of the ground cable to the "Welding current" +" socket (1e) at the power source and
screw hand-tight.
10. Clamp the "Ground cable" clamp (6a) of the ground cable to the workpiece (3b). Ensure good electrical contact (if necessary,
grind the workpiece surface down to the bare metal).
11. If applicable, connect the "Remote control" plug (4a) in the "Remote control" socket (1g) to the power source. Remove the
dummy plug beforehand.
12. Switch on the welding power supply.
13. Carry out a gas and cooling liquid function test. (see chap. 8.7, p. 99). If necessary, top up the cooling liquid.
8.2.2
Connecting the welding tongs to the power source: TP AVC/OSC
NOTE!
X Ensure before connecting the welding tongs that the power source is switched off.
NOTE!
The remote control for using the TP AVC/OSC welding tongs is mandatory and must be
ordered separately (included in the scope of delivery of the AVC/OSC power source).
86
ORBITALuM TOOLS GmbH D-78224 Singen www.orbitalum.com
ORBIWELD TP 400, TP 600
[REV. 20231027] OW_ORBIWELD_TP_BA_812060201_01__INH-01_EN
ORBIWELD TP 400, TP 600
8.2.2.1
Connection scheme TP AVC/OSC
1
3
2
2a
1b
3a
2b
1d
3b
2c
1a
2d
1c
5
2e
1h
2f
5c
2g
1j
2h
1i
[REV. 20231027] OW_ORBIWELD_TP_BA_812060201_01__INH-01_EN
ENGLISH
Setup and mounting
1i
1j
1k
1 g
1f
5b
1b
1c
2d
1e
6b
1d
2b
1a
1h
4
5a
4a
6a
6
6a
3b
5a
3a
6b
5b
1f
6c
5c
2f
Orbitalum Tools GmbH D-78224 Singen www.orbitalum.com
2h
2g
6c
4a
2a
2c
2e
1 g
1e
1k
87
Publicidad
