Final Shut-Down; Automatic Operation - Van Berkel International VOLANO Serie Manual Del Usuario

plate. A safety device will stop
the motor, stopping carriage
feeding, but excessive prod-
uct pressing against the plate
could cause the first slice to be
coarse and irregular.
- Set the desired slice thick-
ness by means of the buttons
(F).
- Slice thickness can be in-
creased 5 hundredths of a
millimetre at a time up to 1
millimetre of thickness. After
one millimetre, the increase is
0.1 mm at a time up to 7 mm of
thickness.
- Activate the blade by press-
ing the button (B).
SEMI-AUTOMATIC
OPERATION FOR MODELS:
Semi-automatic Volano S9M,
Automatic Volano SE9 37E
WARNING! The AUTO-
!
MATIC FLYWHEEL SE9
37E MODEL can be used both
in semi-automatic and in auto-
matic mode.
- Press and hold the blade start
button with the left hand and
activate the flywheel, having
it rotate in the clockwise di-
rection. When the blade guard
plate moves, release the but-
ton (B) and continue turning
the flywheel. The product will
feed forward and a slice of the
previously set thickness will be
obtained.
TEMPORARY STOP
- Rotate the flywheel until the
carriage is moved completely
toward the operator, then stop
rotation and stop the blade
by pressing the button (I). The
front blade guard plate will
return to the original closed
position.
WARNING! Stop fly-
!
wheel rotation and, after
approximately 20 seconds, the
front blade guard plate will au-
tomatically return to the origi-
nal position.

FINAL SHUT-DOWN

- After having followed the
instructions for a temporary
stop, complete shut-down by
pressing the button (A).
- Enable the slice counter func-
tion (G) (LED on). Set the num-
ber of slices to be cut.
WARNING!
!
Counter not enabled:
display 000, continuous cut-
ting.
Counter enabled: the number
of slices to be cut, from 001 to
999, can be set on the display.
WARNING! An acoustic signal
will warn the operator when
the set number of slices has
been reached.

AUTOMATIC OPERATION

- Completely rotate the car-
riage speed adjustment knob
(D) in the anticlockwise direc-
tion.
- If you wish to slice automat-
ically, switch on the slice coun-
ter device (G) (LED on) and set
the number of slices by means
of the buttons (H).
WARNING! If no num-
!
ber has been set and 000
appears on the display: cutting
is not permitted.
- Fold down the flywheel grip,
pulling it toward the operator,
and reposition it against the
flywheel itself.
- Start cutting operations by
starting up the carriage (C).
The product will feed forward
and a slice of the previously set
thickness will be obtained.
- To adjust speed, rotate the
knob (D) in the clockwise di-
rection.
8
DURING CUTTING
- The counter can be enabled
or disabled (G).
- The value set on the slice
counter display (H) can be ed-
ited.
- TEMPORARY STOP
- Press the button (L) and wait
for the carriage to stop.
- Stop the blade (I); the front
blade guard plate will move
transversely, returning to the
original closed position.
WARNING! To prevent
!
the carriage from block-
ing during cutting, never stop
the blade before stopping the
carriage. Stop carriage move-
ment and the front blade guard
plate will move automatically
after 20 seconds, returning to
its original position.
- To re-start cutting, start the
blade by pressing the button
(B) and repeat the operations
listed in the paragraph on "AU-
TOMATIC OPERATION".
! WARNING!
temporary stop with the
counter enabled, cutting will
re-start with the slice counter
display showing the residual
value.
WARNING! Cutting can
!
be started in manual
mode by rotating the flywheel
in the clockwise direction be-
fore the front blade guard
plate repositions.
FINAL SHUT-DOWN
- Perform operations as with a
temporary stop and then press
the button (A).
EMERGENCY STOP
- For immediate
stop, press the red mush-
room-shaped button (Fig. 4-A)
all the way down. In automat-
ic operating mode, also check
that the carriage has stopped.
WARNING! The button
!
(Fig. 4-A) maintains its
After a
blade