Setting Parameters - Van Berkel International VOLANO Serie Manual Del Usuario

position when activated.
RESET AFTER AN EMERGEN-
CY STOP
- Rotate the button in the
clockwise direction and bring it
to the raised position (Fig. 4-B):
the blade cover gauge plate
will return to its original posi-
tion. Resume cutting activity in
the preferred mode.
ERROR MESSAGES ON THE
"SLICE THICKNESS"
"NUMBER OF CUTS" DIS-
PLAYS
Upon blade start-up:
1. 00 – Err: emergency stop
button activated - solution:
rotate the button in the clock-
wise direction;
2. 03 - Err: blade not present
or incorrectly positioned –
solution: check correct blade
position;
3. 05 – Err: set number of cuts
= 0 – solution: deactivate the
counter or set a value.
Upon carriage start-up in auto-
matic mode:
1. 06 – Err: meat table against
the front blade guard plate -
solution: move the meat table
away by pressing the button
(E);
2. 07 – Err: meat table not
present – solution: verify cor-
rect table positioning.
! WARNING! If error sig-
nals persist even after
the appropriate checks have
been made, contact Van Berkel
International service
tance (see the par. on "Assis-
tance").
During blade sharpening:
1. 01 – SHR: if the mobile
blade guard opens or is not
present during sharpening de-
vice cover lifting;
2. 02 – SHR: when the sharp-
ening device is lifted;
3. 03 – SHR: when the sharp-
ening device is rotated toward
the blade in the working posi-
tion.
PROGRAMMING

SETTING PARAMETERS

Make sure that the slicer is in
"final shut-down" mode and
press the slice counter in-
AND crease/decrease buttons at the
same time to access parame-
ters as follows:
1. ACOUSTIC SIGNAL ENA-
BLE (00 o 01)
PARAMETER P.00
DEFAULT VALUE: Press the
+ and – buttons to edit the
value:
default value 00: acoustic sig-
nal only in the event of anom-
alies or at the end of work;
default value 01: acoustic sig-
nal also when each button is
pressed.
To go to the next parameter,
press the + and – buttons.
2. AUTOMATIC SHUT-DOWN
ENABLE (from 00 to 99)
PARAMETER P.01
DEFAULT VALUE: press +
and – buttons of the default
value to set minutes:
default value 00: disables this
function;
default value from 01 to 99:
sets the minutes after which
the slicer will switch off auto-
matically.
3. AUTOMATIC BLADE ROTA-
assis- TION STOP (from 00 to 99)
PARAMETER P.02
DEFAULT VALUE: press +
and – buttons of the default
value:
default value 00: disables this
function;
default value from 01 to 99:
sets the minutes after which
the slicer will switch off auto-
4.
AWAY FROM BLADE (from 00
to 99)
5.
BLADE GUARD PLATE CLOS-
ING DELAY TIME (from 00 to
25)
9
matically.
PRODUCT DISTANCE
After cutting slices, the car-
riage returns toward the op-
erator, rubbing the product
against the blade. When a dis-
tance is set, the carriage can
move away from the blade
before returning toward the
operator, avoiding product
rubbing.
PARAMETER P.03
DEFAULT VALUE: allows the
user to set the distance be-
tween the meat table and the
blade during the table return
phase.
WARNING!! The de-
!
fault values
sponding to relative parame-
ters must not be changed.
DEFAULT VALUE: 10 – PA-
RAMETER: P04
DEFAULT VALUE: 20 – PA-
RAMETER: P05
DEFAULT VALUE: 20 – PA-
RAMETER: P06
DEFAULT VALUE: 10 – PA-
RAMETER: P07
DEFAULT VALUE: 08 – PA-
RAMETER: P09
DEFAULT VALUE: 15 – PA-
RAMETER: P10
AUTOMATIC
PARAMETER P. 08
DEFAULT VALUE: allows the
user to set the maximum time
that the carriage is stopped
(no operations in progress)
before the front blade guard
plate automatically re-closes.
Default value 00: automatic
closing is disabled; therefore,
the plate only re-closes when
the blade is shut down.
Press the button (A) (LED
corre-
FRONT