Attachments With Three-Jaw Chuck Gb621R/Gb639R/Gb667R; Zimmer Chuck With Hudson/Zimmer Shaft Gb176R; Harris Chuck With Ao Large Shaft Gb184R And Din Chuck With; Ao Large Shaft Xf457R - Aesculap Acculan 4 Instrucciones De Manejo

Uncoupling
►
Rotate the locking sleeve 11 clockwise and open Jacobs chuck.
►
Remove tool.
►
Rotate the locking sleeve 11 counterclockwise and close Jacobs chuck.
6.4.3 Attachments with three-jaw chuck
GB621R/GB639R/GB667R
Coupling
►
Open the Jacobs chuck with the key 13.
►
Insert the tool shaft in the correct position up to the st op in the tool
holder 8 of the attachment 12.
►
Close the Jacobs chuck with the key 13 and pull tight.
►
Pull at tool to check that it is securely coupled.
Uncoupling
►
Open the Jacobs chuck with the key 13.
►
Remove tool.
6.4.4

Zimmer chuck with Hudson/Zimmer shaft GB176R

Coupling
►
Push unlocking sleeve forward 15 and hold.
►
Insert the tool shaft in the correct position up to the st op in the tool
holder 8 of the attachment 14.
►
Release the unlocking sleeve 15.
►
Pull at tool to check that it is securely coupled.
Uncoupling
►
Push unlocking sleeve forward 15 and hold.
►
Remove tool.
6.4.5

Harris chuck with AO large shaft GB184R and DIN chuck with

AO large shaft XF457R

Coupling
►
Push unlocking sleeve back 15 and hold.
►
Insert the tool shaft in the correct position up to the st op in the tool
holder 8 of the attachment 14.
►
Release the unlocking sleeve 15.
►
Pull at tool to check that it is securely coupled.
Uncoupling
►
Push unlocking sleeve back 15 and hold.
►
Remove tool.
6.4.6

Adapter AO large to DHS/DCS step drill GB628R

Coupling
►
Push unlocking sleeve back 15 and hold.
►
Insert the tool shaft in the correct position up to the st op in the tool
holder 8 of the attachment 16.
►
Release the unlocking sleeve 15.
►
Pull at tool to check that it is securely coupled.
Uncoupling
►
Push unlocking sleeve back 15 and hold.
►
Remove tool.
6
6.4.7

Sagittal saw attachment GB660R

Coupling
►
Insert saw blade 25 into the slot of the tool holder 18, see Fig. A.
Ensure that the side stops of the saw blade are aligned with the tool
holder.
The tool engages.
►
Pull on the attachment 22 to ensure a secure fit.
Uncoupling
►
Press kjnob for tool release 19 and pull saw blade 25 out of the tool
holder 18.
6.4.8

Drill attachment for Synthes radiolucent angle transmission

GB645R

The drill attachment allows connecting a radiolucent angle transmission
for applying drill holes in the bone under radiographic control.
The drill attachment is only suitable for use of the radiolucent angle trans-
mission 511.300 from the Synthes company.
►
Follow the instructions for the radiolucent angle transmission 511.300
in the operating instructions of the Synthes company.
Coupling the angle transmission
►
Push the radiolucent angle transmission up to the stop on holder 8 of
the drill attachment 20.
►
If necessary, slightly move the radiolucent unit.
Decouple angled handpiece
►
Forcefully pull out the radiolucent angle transmission from the drill
attachment 20.
Couple/decouple the tool
►
Follow the instructions for the radiolucent angle transmission 511.300
in the operating instructions of the Synthes company.
6.4.9

Insert and clamp Kirschner wire attachment GB641R

Risk of injury when using long guide wires!
►
Use Kirschner wire protection sleeve when using
long guide wires.
WARNING
Note
The special Kirschner wire chuck is recommended for the placement of
guide wires. This quick-action chuck adapter allows quick and easy ten-
sioning of drilling wires.
For further information see TA014535 or TA014539 (flyer).
The following diameters can be set on the Kirschner wire attachment:
■
0.6 mm to 1.8 mm
■
1.8 mm to 3.0 mm
■
3.0 mm to 4.0 mm
Insert Kirschner wire
►
Ensure that the clamping lever 22 is in the starting position (deacti-
vated status).
►
Set the adjusting sleeve 23 of the Kirschner wire attachment to the
desired diameter range:
– Push back the adjusting sleeve 23 and turn until the desired diam-
eter range has been reached.
– Release adjustment sleeve 23, making certain that adjustment
sleeve 23 clicks into position.
►
Insert the Kirschner wire into the Kirschner wire chuck 24 until the
desired exposed length is achieved.
The Kirschner wire is held in the intended position in the attachment
by an automatic clamping mechanism.