Publicidad
Idiomas disponibles
Idiomas disponibles
EN
4 Troubleshooting
4.1 Troubleshooting
Fault
Possible cause
Poor contact of power plug
The tip does not vibrate
and no water comes out
Poor contact of pedal switch
after powering on and
stepping on the foot
The fuse is broken
switch
Out of battery under wireless
pedal mode
Poor connection under wired
pedal mode
Main unit fault
Loose tip
The tip does not vibrate
and
The connection between
there is water spray after
the tail wire and the circuit board is loose.
power on and
stepping on the foot
Handpiece fault
pedal.
Cable fault
The resistance of the diaphragm pump
The tip vibrates but there
becomes larger, and the torque of the low
is no water spray after
water retaining capacity is insufficient
power on and stepping
on the foot pedal.
Impurity in the solenoid valve
Water line clogging
Impurity in the solenoid valve
After power-off, there is
still water spray.
Water volume is too small
Handpiece heating
Device fault
Water volume is too small
Water spray is too small
Water line clogging
Tip is not tightened.
Weakened tip vibration
Tip is loose
Broken tip (Note1)
Outlet water
Thermocouple fault
temperature is too
high (over 45° C)
The nut is not tightened
The Endo file does not
vibrate
Loose contact of power supply plug.
There is no air spray and
water spray after power
Poor connection under wired pedal mode
on and stepping on the
foot pedal.
Out of battery under wireless pedal mode
Nozzle clogging
The nozzle does not
spray gas but there is
Handpiece clogging
water spray after power
on and stepping on the
Clogging of handpiece tail cord
foot pedal.
Solenoid valve fault
The resistance of the diaphragm pump
There is air flow but no
becomes larger, and the torque of the low
water spray after power
water retaining capacity is insufficient
on and stepping on the
foot pedal.
Impurity in the solenoid valve
Water line clogging
The O-ring on base of powder
Leaking air of powder
tank is broken
tank
Broken O-ring
There is powder residue at the thread, so that
the screw is not in place.
The upper cover of powder tank
is broken.
The thread of powder tank is broken
so that the screw is not in place
Broken O-ring of handpiece
Water leakage of
handpiece
The powder in tank is not enough
The air powder scaling
efficiency is reduced.
Powder residue in pipe, handpiece, or
nozzle passage
No powder tank
Touch panel pops up
prompt message
Air pressure is too high or too low
Pick up two handpieces at a time
No handpiece has been picked up
The handpiece does not match the mode
configuration
Note: if the problems cannot be solved, please contact local distributor or the manufacturer.
4.2 Notes
Note1 If the tip is surely tightened and there is water mist spray, the tip is considered to be
damaged with the following phenomena:
1) The vibration intensity of the tip and the degree of water atomization are significantly
weakened.
2) The tip makes a harsh click sound during operation.
6 |
Instruction Manual
_R0_XPOWER ablatore_bug_6lingue.indd 6
_R0_XPOWER ablatore_bug_6lingue.indd 6
5 Cleaning, disinfection, and sterilization
5.1
Solutions
Plug the foot pedal plug well.
5.2
Plug the power supply well
Replace a T1.6AL 250V fuse
Replace a new battery
Notice:
Connect the wire and screw it well
a) Clean the handpiece with compressed air before sterilization.
Contact local distributor or the manufacturer.
b) Be sure that the tip has been unscrewed from the handpiece and it cannot be sterilized
Tighten the tip
c) Please notice whether the outer of the handpiece is damaged during the treatment and
Contact local distributor or the manufacturer.
Contact local distributor or the manufacturer.
d) There are some waterproof "O" rings at the end of the handpiece. Please lubricate them
Contact local distributor or the manufacturer.
e) The following sterilizing methods are forbidden:
Turn up the water volume.
• Boil in water.
Contact local distributor or the manufacturer.
• Dip in iodine, alcohol and glutaraldehyde.
Contact local distributor or the manufacturer.
• Bake in oven or microwave oven.
Notice: We are not responsible for any damage caused in the above items.
Contact local distributor or the manufacturer.
6 Transport , storage and maintenance
Turn up the water volume
Contact local distributor or the manufacturer.
6.1 Transport
Turn up the water volume
6.1.1 Excessive impact and shake should be prevented during transport. Lay it care fully
Contact local distributor or the manufacturer.
Tighten the tip
6.1.2 Do not put it together with dangerous goods during transport.
Tighten the tip
6.1.3 Avoid being exposed to sun, rain, and snow during transport.
Remove the tip
6.2 Storage
Contact local distributor or the manufacturer.
6.2.1 The device should be handled carefully and lightly. Be sure that it is far from the vibra-
Tighten the nut
6.2.2 Do not store the machine together with articles that is poisonous, combustible, caustic,
Plug the power supply plug well
6.2.3 This machine should be stored in a room where the relative humidity is 10% - 93%,
Connect the wire and screw it well
Replace a new battery
6.2.4 When the device is not in use, turn off the power supply and unplug the power plug. If
Dredge the nozzle
Dredge the handpiece
Remove the tail cord from the
6.3 maintenance
main unit, dredge the tail cord or replace it.
Contact local distributor or the manufacturer
6.3.1 Air filter
1) When water accumulate in the filter, turn the knob at the bottom of the filter counterclo-
Turn up the water volume
2) Replacement of the filter element: Use a filter wrench to unscrew the transparent cover
Contact local distributor or the manufacturer
Contact local distributor or the manufacturer
Unscrew the powder tank base, take out
the damaged O-ring, replace the O-ring of
the same specification attached, and
It is recommended to replace the filter element every 24 months, and the spare filter ele-
screw on the powder tank base
Replace the O-ring
Remove the residual powder at the thread
part.
Replace the upper cover of powder tank
Replace a powder tank
Replace the O-ring
Add powder to the tank
Clean the passage with a fine needle and
blow it off with compressed air
7 Environmental Protection
Check the powder tank and reinstall
The instrument contains no hazardous components and can be disposed of and destroyed in
Increase the external air pressure input,
Input air pressure range requirements:
accordance with the relevant local regulations.
5.5bar-7.5bar(0.55Mpa-0.75MPa)
Before stepping on the pedals, please pick up
only one handpiece
Before stepping on the pedals, please pick up
Part
only one handpiece
Please select the correct handpiece and
Main unit
mode
Handpiece
Tip
Nozzle Foot pedal
Mechanical elements, including bolts,
nuts, washers, etc.
○ : Indicates that the content of the toxic substance in all homogeneous materials of the part is
below the limit requirement stipulated in SJ/T-11363-2006 Limit Requirements for Toxic and Haz-
ardous Substances in Electronic Information Products.
X:indicates that the content of the toxic substance in at least one of the homogeneous
materials of the part exceed the limit requirement specified in SJ/T-11363-2006. Please dispose
according to the local laws or consult with dealer from whom you purchased it about waste dis-
posal.
Please conform to the recommendations of the attachment "Reprocessing Instructions
of Cleaning, Disinfecting and Sterilizing" delivered with your product regarding the pro-
cedure of cleaning, disinfecting, sterilizing and packing of the components. Follow pres-
ent-day regulations enforced in the country about reprocessing. The use of scouring
powder or an abrasive sponge will damage its surface.
The handpiece, tips, torque wrench, endo wrench, LED lamp and Light conductor (the
handpiece with LED lamp) can be sterilized.
• Recommended sterilization cycles of handpiece: 300 cycles
• Recommended sterilization cycles of torque wrench and endo wrench: 300 cycles
with others.
sterilization. Don't smear any protective oil on the surface of handpiece.
with dental lube frequently, as sterilization and repeated pulling and inserting will reduce
their using life. Change a new one once it is damaged or worn excessively.
and lightly.
tion, and installed or kept in a cool, dry, and ventilated place.
or explosive.
atmospheric pressure is 70kPa - 106kPa, and the temperature is-20°C - +5°C .
it is not used for a long time, it should be energized and connect to water and air once
a month for five minutes.
ckwise to drain the water, and tighten the knob clockwise.
of the air filter, then use the wrench to unscrew the black nut at the lower end of the filter
element, remove the white filter element and discard it into the trash can, re- place it with
a new filter element, and reinstall the black nut and transparent shell.
ment is included in the accessory.
Pb
Figure 11.
Schematic diagram
of filter element
replacement
Toxic or harmful substances or elements
Hg
Cd
Cr6+ PBB PBDE
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
○
02/07/24 16:55
02/07/24 16:55
Publicidad
