Publicidad
Idiomas disponibles
Idiomas disponibles
P11.19
P11.20
P11 – Settings EQUIP 2
P11.21
P11.22
P11.23
P11.24
Setup of equipment 3 is divided into a series of menus, which are grouped by function.
This group's access is allowed for administrator users.
P12.01*
P12.02*
P12.03*
P12.04*
Setup EQUIP 3
P12.05*
P12.06
P12.07
P12.08
P12.08.01
P12.08.02
P12.08.03
P12.08.04
P12.09
Press ENTER to access the sub-menus - *Editable only when the machine is stopped
Reading and editing with keyboard or ECO card
Used to configure a variety of maintenance services 6.
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set between 'OFF' (that is, without scheduling) or between the
Maintenance hours 6
following services: air filter check, oil filter check, belt check, dust cleaning of compartment filters, oil change, separator
check, grease bearings, exhaust check, dryer check, electrical part check, lubrication, valve check, flow vs pressure and unit
check. Press 'ENTER'. The set value is stored in memory and the browser returns to P11.19.
Note: set the hours in parameter P16.06.
Used to configure a variety of maintenance services 7.
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set between 'OFF' (that is, without scheduling) or between the
Maintenance hours 7
following services: air filter check, oil filter check, belt check, dust cleaning of compartment filters, oil change, separator
check, grease bearings, exhaust check, dryer check, electrical part check, lubrication, valve check, flow vs pressure and unit
check. Press 'ENTER'. The set value is stored in memory and the browser returns to P11.20.
Note: set the hours in parameter P16.07.
Used to configure a variety of maintenance services 8.
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set between 'OFF' (that is, without scheduling) or between the
Maintenance hours 8
following services: air filter check, oil filter check, belt check, dust cleaning of compartment filters, oil change, separator
check, grease bearings, exhaust check, dryer check, electrical part check, lubrication, valve check, flow vs pressure and unit
check. Press 'ENTER'. The set value is stored in memory and the browser returns to P11.21.
Note: set the hours in parameter P16.08.
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set between 'ON' and 'OFF'. Press ENTER. The set value is stored in
Weekly maintenance
memory and the browser returns to P11.19.
Note: set the hours in parameter P16.06.
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set between 'ON' and 'OFF'. Press ENTER. The set value is stored in
Annual maintenance
memory and the browser returns to P11.20.
Note: set the hours in parameter P16.07.
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set between 'ON' and 'OFF'. Press ENTER. The set value is stored in
Biannual maintenance
memory and the browser returns to P11.21.
Note: set the hours in parameter P16.08.
The default values are defined by the software configuration file.
Reset parameters
Press 'ENTER'. Use the 'UP' arrow to select 'YES'. Press 'ENTER'. The default values are reset.
Note: The reset is logged in the event log.
Creates a new setup file, overwriting the existing file. Press 'ENTER'. Use the 'UP' arrow to select 'YES'. Press 'ENTER'.
Current parameters are stored in the configuration file.
Save as SETUP
Notes: understand how the interface manages parameter data.
- The default values are defined by the software configuration file.
- Current parameters are set during normal operation, and may differ from the original setup file.
- By resetting the parameters, current values are replaced by the current configuration file (original or saved later).
Use of pressure sensor with custom reading range. The default pressure sensor is from 0 to 16 BAR (or other selectable
Use custom SEN
unit). To use a different reading range, press 'ENTER', select 'ON', press 'ENTER' again. The parameter is stored and the
menu returns to P12.03.
Compressor outlet pressure reading range. Press 'ENTER'. Set the desired pressure. Press 'ENTER' again. The parameter
value is stored and the menu returns to P12.04.
PRESSURE Range
Note: The standard is 4-20mA signal, with 4mA equivalent to minimum pressure and 20mA equivalent to maximum.
Compressor internal pressure reading range. Press 'ENTER'. Set the desired pressure. Press 'ENTER' again. The parameter
value is stored and the menu returns to P12.05.
Internal PRESSURE range
Note: The standard is 4-20mA signal, with 4mA equivalent to minimum pressure and 20mA equivalent to maximum.
Deletes the error log. Press 'ENTER'. Use the 'UP' arrow to select 'YES'. Press 'ENTER'. The error log will be deleted and
Reset reg errors
the menu will return to P12.06.
Deletes the event log. Press 'ENTER'. Use the 'UP' arrow to select 'YES'. Press 'ENTER'. The event log will be deleted and
Reset reg events
the menu will return to P12.07.
Total hours worked since the technical start.
HRS total STR
Note: The set date must match the technical start date.
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set the corresponding year. Press 'ENTER'. The set value is stored in
Year
memory and the browser returns to P12.08.01.
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set the corresponding month. Press 'ENTER'. The set value is stored in
Month
memory and the browser returns to P12.08.02.
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set the corresponding day. Press 'ENTER'. The set value is stored in
Day
memory and the browser returns to P12.08.03.
Press 'ENTER'. The values set in P12.08.01 ~ P12.08.03 will be stored in memory and the browser will return to P12.08.
Date
Note: You need to save the new values set in P12.08.01 - P12.08.03 using P12.08.04 before leaving the sub-
-menu.
Setting load hours. It is typically used to clear the hours before the technical start or to synchronize with another external
timer.
Ajust load HRS
Press 'ENTER'. Use the 'UP' and 'DOWN' arrows to set the value. Press 'ENTER'. The set value is stored in memory and the
browser returns to P12.09.
213
Publicidad
