Intended Use; Residual Risks; General Safety Rules - Homelite HCS3335A Manual De Utilización

EN
FR DE ES IT PT
Figure 59
92. Air filter
Figure 61
25. Idle speed screw "T"
Figure 62
93. Chain brake
5. Chain lubricant cap
16. Fuel cap
94. Post
95. Starter cover
Figure 63
96. Clean engine fins
Figure 64
97. Clean flywheel fins
Figure 65
98. Fuel filter
Figure 67
99. Deflector
100. Deflector retaining screw
101. Spark arrestor
20. Silencer
Figure 68
24. Clean the chain brake

INTENDED USE

This chainsaw is designed for cutting wood such
as branches, trunks, logs and beams of a diameter
determined by the cutting length of the guide bar, and
not to be used for any other purpose. The product is also
not to be used for professional tree services. It is to be
used by adults and not children or by persons not wearing
adequate personal protective equipment and clothing.

RESIDUAL RISKS:

Even when using the chainsaw as intended, there remains
a residual risk of harm which cannot be fully prevented.
The following list of potential hazards should be read and
understood. You should pay extra attention and care to
these items to reduce the risk of injury.
Contact with exposed cutting teeth and saw chain.
Q
Access to rotating parts (the saw chain)
Q
Unexpected, abrupt movement (kick back) of the guide
Q
bar.
Flying chain parts (thrown off or broken)
Q
Flying material (cut from the work piece)
Q
Inhalation of saw dust and particles or emissions from
Q
the petrol engine.
Skin contact with petrol / oil.
Q
Loss of hearing if no hearing protective equipment is
Q
worn during use.
960390004-05.indd Sec1:27 960390004-05.indd Sec1:27
NL SV DA NO FI HU CS RU
English(original instructions)

GENERAL SAFETY RULES

READ ALL INSTRUCTIONS
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
Q
27
RO PL SL HR ET
WARNING
Read and understand all instructions. Failure to
follow all instructions listed below may result in fire
and/or serious personal injury.
Know your tool. Read the operator's manual carefully.
Learn the saw's applications and limitations as well as
the specific potential hazards related to this tool.
Kickback may occur when the nose or tip of the guide
bar touches an object, or when the wood closes in and
pinches the saw chain in the cut. Tip contact in some
cases may cause a lightning-fast reverse reaction,
kicking the guide bar up and back toward the operator.
Pinching the saw chain along the top of the guide
bar may push the guide bar rapidly back toward the
operator. Either of these reactions may cause you to
lose control of the saw, which could result in serious
personal injury. Do not rely exclusively upon the safety
devices built into the saw. As a chainsaw user, you
should take every step to keep your cutting jobs free
from accident and injury.
With a basic understanding of kickback, you can
reduce or eliminate the element of surprise. Sudden
surprise contributes to accidents.
Keep a good firm grip on the saw with both hands
when the engine is running. Place your right hand on
the rear handle and your left hand on the front handle
with your thumbs and fingers encircling the chainsaw
handles. A firm grip together with a stiff left arm will help
you maintain control of the saw if kickback occurs.
Make sure that the area in which you are cutting is free
from obstructions. Do not let the nose of the guide bar
contact a log, branch, fence, or any other obstruction
that could be hit while you are operating the saw.
Always cut with the engine running at full speed. Fully
squeeze the throttle trigger and maintain a steady
cutting speed.
Do not overreach or cut above chest height.
Follow the manufacturer 's sharpening and
maintenance instructions for the saw chain.
Only use replacement bars and chains specified by the
manufacturer or the equivalent.
Do not operate a chainsaw with one hand. Serious
injury to the operator, helpers, bystanders, may result
from one-handed operation. A chainsaw is intended for
two-handed use.
Do not operate a chainsaw when you are fatigued.
Fatigue causes carelessness. Be more cautious
before rest periods and towards the end of your shift.
LT LV SK BG
22/02/2010 4:05 PM 22/02/2010 4:05 PM