Publicidad
Idiomas disponibles
Idiomas disponibles
b. If you do not know the mechanical data, for example, in modernization case, you can use the speed ratio
to determine the mechanics:
i. Set the speed of the elevator car to o1-18 [Speed of Elevator Car].
ii. Set the elevator motor speed to o1-19 [Elevator Motor Speed].
Note:
When you use the speed ratio, the drive ignores the dedicated mechanical parameters (o1-2x)
Refer to
Drive Parameters on page 27
■
Drive Parameters
Refer to the following table to set the most important parameters.
Note:
• You can change parameters that have "RUN" in the "No." column during drive operation.
• Parameters that have "Expert" in the "No." column are available in Expert Mode only. Set A1-01 = 3 [Access Level Selection = Expert
Level] to show and set Expert Mode parameters on the keypad.
No.
A1-00
Language Selection
RUN
A1-02
Control Method Selection
A1-03
Initialize Parameters
b1-01
Speed Reference Selection 1
b1-02
Up/Down Command Selection 1
b1-03
Stopping Method Selection
C1-01
Acceleration Ramp 1
RUN
C1-02
Deceleration Ramp 1
RUN
C2-01
Jerk @ Start of Accel
C2-02
Jerk @ End of Accel
C2-03
Jerk @ Start of Decel
C2-04
Jerk @ End of Decel
C2-05
Jerk below Leveling Speed
C5-01
ASR Proportional Gain 1
RUN
C5-02
ASR Integral Time 1
RUN
C5-03
ASR Proportional Gain 2
RUN
C5-04
ASR Integral Time 2
RUN
C5-13
ASR Proportional Gain 3
RUN
C5-14
ASR Integral Time 3
RUN
C6-03
Carrier Frequency
d1-01 - d1-08
Reference 1 to 8
RUN
d1-18
Speed Reference Selection Mode
d1-19
Nominal Speed
RUN
YASKAWA TOMPYEULA7002A LA700 Series Installation and Operation Instruction
for more information.
Name
Sets the language for the LCD keypad.
0: English, 1: Japanese, 2: German, 3: French, 4: Italian, 5: Spanish, 6: Portuguese, 7: Chinese, 8: Czech, 9: Russian,
10: Turkish, 11: Polish, 12: Greek
Sets the control method for the drive application and the motor.
0: V/f Control, 2: Open Loop Vector, 3: Closed Loop Vector, 7: PM Closed Loop Vector
Sets parameters to default values.
0: No Initialization, 1110: User Initialization, 2220: 2-Wire Initialization
Sets the input method for the speed reference.
0: Keypad, 1: Analog Input, 2: Memobus/Modbus Communications, 3: Option PCB
Sets the input method for the Up/Down command.
0: Keypad, 1: Digital Input, 2: Memobus/Modbus Communications, 3: Option PCB
Sets the method to stop the motor after removing an Up/Down command or entering a Stop command.
0: Ramp to Stop, 1: Coast to Stop, 4: Elevator Emergency Stop
Sets the ramp to accelerate from zero to maximum output speed.
Sets the ramp to decelerate from maximum output speed to zero.
Sets the jerk at the start of acceleration.
Sets the jerk at the completion of acceleration.
Sets the jerk at the start of deceleration.
Sets the jerk at the completion of deceleration.
Sets the jerk when the speed reference is lower than the leveling speed setting.
Sets the gain to adjust ASR response at high speed.
Sets the ASR integral time at high speed.
Sets the gain to adjust ASR response at low speed.
Sets the ASR integral time at low speed.
Set the gain to adjust ASR response at leveling speed. The setting is active for deceleration only.
Sets the ASR integral time at leveling speed. The setting is active for deceleration only.
Sets the carrier frequency.
Sets the speed reference in the units from o1-03 [Speed Display Unit Selection].
Sets the mode of speed reference selection by digital inputs.
0: Multi-speed Mode1 (d1-01 to 08), 1: High speed has priority, 2: Leveling speed has priority,
3: Multi-speed Mode2 (d1-02 to 08), 4: Smart Replacement
Sets the nominal speed reference when an MFDI terminal set for H1-xx = 50 [MFDI Function Selection = Nominal
Speed] is active.
Description
1 English
27
Publicidad
