Descargar Imprimir esta página

Stryker 1588 AIM Manual Del Usuario página 17

Publicidad

Idiomas disponibles
  • MX

Idiomas disponibles

  • MEXICANO, página 290
N N o o t t e e - - To remove the coupler, grip the rear adapter and unscrew the coupler
counterclockwise from the camera head.
2. Attach an endoscope to the coupler.
W W A A R R N N I I N N G G - - B B e e f f o o r r e e e e a a c c h h u u s s e e , , c c h h e e c c k k t t h h e e o o u u t t e e r r s s u u r r f f a a c c e e o o f f t t h h e e e e n n d d o o s s c c o o p p e e t t o o e e n n s s u u r r e e t t h h e e r r e e
a a r r e e n n o o r r o o u u g g h h s s u u r r f f a a c c e e s s , , s s h h a a r r p p e e d d g g e e s s , , o o r r p p r r o o t t r r u u s s i i o o n n s s . .
N N o o t t e e - - For a list of endoscopes that are compatible with ENV mode, see Stryker user manual
P27006 (English) or P27009 (multilingual) for the L10 LED Light Source with AIM Technology.
Remove the coupler dust cap if it is present.
Depress the endobody clamp
Release the endobody clamp to secure the endoscope.
3. Attach a light cable from the light source to the light post on the endoscope
N N o o t t e e - - A scope adapter may be required to connect the cable to the endoscope. See the light
cable user manual for more detail.
N N o o t t e e - - Only the Stryker AIM SafeLight™ cable (0233-050-300) is compatible with ENV mode.
ENV mode will not function if other cables are used. Refer to the AIM SafeLight cable user
manual (P27701) for complete cable instructions.
W W A A R R N N I I N N G G - - W W h h e e n n c c o o n n n n e e c c t t i i n n g g a a n n A A I I M M S S a a f f e e L L i i g g h h t t c c a a b b l l e e t t o o t t h h e e e e n n d d o o s s c c o o p p e e , , a a l l w w a a y y s s
c c o o n n n n e e c c t t t t h h e e s s c c o o p p e e a a d d a a p p t t e e r r t t o o t t h h e e e e n n d d o o s s c c o o p p e e b b e e f f o o r r e e c c o o n n n n e e c c t t i i n n g g t t h h e e a a d d a a p p t t e e r r t t o o t t h h e e
c c a a b b l l e e . . I I f f E E N N V V m m o o d d e e i i s s e e n n a a b b l l e e d d a a n n d d t t h h e e a a d d a a p p t t e e r r i i s s n n o o t t c c o o n n n n e e c c t t e e d d t t o o t t h h e e s s c c o o p p e e , , l l a a s s e e r r
r r a a d d i i a a t t i i o o n n w w i i l l l l e e m m i i t t f f r r o o m m t t h h e e a a d d a a p p t t e e r r t t h h a a t t c c a a n n c c a a u u s s e e s s e e v v e e r r e e e e y y e e i i n n j j u u r r y y t t o o t t h h e e p p a a t t i i e e n n t t o o r r
u u s s e e r r . .
I I n n s s t t a a l l l l i i n n g g t t h h e e S S o o a a k k i i n n g g C C a a p p
Before reprocessing the camera head, the soaking cap must be installed to avoid damaging the
cable connector.
C C A A U U T T I I O O N N - -
Failure to properly tighten the soaking cap will corrode the connector pins and void the warranty.
To install the soaking cap, screw the cap onto the threads of the cable connector until it forms
a tight seal.
To remove the soaking cap, unscrew the cap and pull it away from the cable connector.
P29924F
1
2
1
and insert a scope into the endobody
3
.
.
15
EN

Publicidad

loading

Este manual también es adecuado para:

1588-010-0001588-210-1051588-610-1221588-710-105