Publicidad
4.7 Test programs
01 Select the "Test cycles"menu
02 Alternatively, directly select "Last test run" and go to step 04
03 Select the desired cycle
04 Screen with all the parameters of the selected cycle
05 (Optional) you can open the door to insert other instruments
06 (Optional) Select the programmed start button to set the start
time
07 Start the test cycle
08 (If anebled) enter the user PIN.
On confirming, the test cycle will start.
09
You can use the green bar to monitor the cycle progress.
10
When the cycle finishes, press the confirm icon to return to
the Home screen.
11-12 You can stop the cycle manually by holding done the
"STOP CYCLE" button for 3 seconds. Wait for the machine
to be put in a safe condition and press the confirm icon (12)
and then press Home to return to the home screen.
14/15 Cycle Validation Protocol: The selection of the Batch, Load
and/or Indicator validation options generates the relative
information in the cycle report: "Batch Ok" – "Batch Fail"
"Indicator OK" - "Indicator Fail" – "No Indicator". "Load
OK" - "Load Fail" - "No Load" * The confirmation button (15)
will be "Operational" when the user makes a selection.
16
For the validation of Batch, Load and/or Indicator, the user
must enter his PIN. When the confirmation button is pressed
(16), the system generates the Cycle Report PDF with the
identification of the User who performed the cycle validation.
4.7
Programmi di test
*Opzione 06 disponibile solo nella versione Premium
36
Pag. 18 - Aggiungere schermata Protocollo Convalida de
PROTOCOLLO DI CONVALIDA DEL CICLO
Pag. 18 - Aggiungere schermata Protocollo Convalida de
CYCLE VALIDATION PROTOCOL
ITA – Protocollo di Convalida del Ciclo
PROTOCOLLO DI CONVALIDA DEL CICLO
ENG - Cycle validation Protocol
CYCLE VALIDATION PROTOCOL
ITA – Protocollo di Convalida del Ciclo
ENG - Cycle validation Protocol
User PIN
User PIN
EN
ITA - Se la gestione
ogni ciclo, alla conf
Protocollo di Conv
Nota: in caso di Cic
Ciclo non è operati
ITA - Se la gestion
ENG - If the Protoc
ogni ciclo, alla con
confirm the selecti
Protocollo di Conv
11
report has not crea
Nota: in caso di Ci
The system propos
Ciclo non è operat
Note: in case of Cy
ENG - If the Proto
confirm the select
11
report has not cre
The system propo
ITA – Protocollo d
Note: in case of C
Indicatore e Caric
"Lotto Ok" – "Lot
14
"Indicatore OK" –
"Carico OK" - "Ca
ITA – Protocollo
* Il pulsante di co
Indicatore e Cari
selezione.
"Lotto Ok" – "Lo
14
ENG – Validation
15
"Indicatore OK"
Indicator validatio
"Carico OK" - "Ca
report:
* Il pulsante di c
"Batch Ok" – "Bat
selezione.
"Indicator OK" - "
"Load OK" - "Load
ENG – Validation
15
* The confirmatio
Indicator validat
selection.
report:
"Batch Ok" – "Ba
"Indicator OK" -
ITA - Per la conv
"Load OK" - "Loa
proprio PIN.
* The confirmati
Alla conferma
selection.
l'identificazione
ENG - For the v
introduce his PI
ITA - Per la con
By the confirma
proprio PIN.
16
with identificat
Alla conferma
l'identificazion
ENG - For the
introduce his P
By the confirm
16
with identifica
59
Publicidad
