Publicidad
19�6 Changing the sterile air filter � � � � � 51
19�7 Function check � � � � � � � � � � � � � � � 52
Troubleshooting
Troubleshooting
6
Troubleshooting guide
20 Tips for operators and
service technicians� � � � � � � � � � � � � � � � 53
6.1 Error Codes
20�1 "Caution" messages � � � � � � � � � � � 53
20�2 "Fault" messages � � � � � � � � � � � � � 53
Code
21 Emergency opening of the door� � � � � � 55
Dooring closing
ER 001
ER 002
Door switch
Appendix
22 Settings menu layout � � � � � � � � � � � � � � 56
Door unlocking timeout
ER 003
Door opening timeout
ER 004
Very poor water quality
ER 006
2
ER 007
Floating feed tank in unexpected condition
ER 100
Vacuum timeout during preheating
ER 101
Pressure rise timeout during preheating
Vacuum pressure timeout
ER 110
Discharge pressure timeout
ER 120
Pressure difference
ER 121
ER 130
Discharge time
Sterilisation pressure timeout
ER 140
ER 141
Pressure difference
ER 150
T chamber high
ER 151
T chamber low
ER 152
T theoretical high
T theoretical low
ER 153
Temperature difference
ER 154
ER 160
Final discharge
Vacuum pressure timeout
ER 171
ER 172
ER 173
Vacuum pressure timeout
ER 180
Balancing timeout
Vacuum test timeout
ER 200
ER 201
Vacuum test: first phase
ER 202
Vacuum test: second phase
Vacuum test: temperature
ER 203
ER 204
Vacuum test: balancing
Vacuum pressure threshold reached timeout
ER 310
Test pressure rise timeout
ER 340
Pressure delta
ER 341
ER 342
Safety valve open
ER 355
Test execution timeout
ER 360
Final discharge timeout
AV lock during drying
ER 370
ER 380
Pressure balancing timeout
Message
timeout
AV block
The door closing time is too long
Door switch error condition
The door unlocking time is too long
The door opening time is too long
The water conducivity is higher than 30uS/cm
6046100064L02 1702V002SE
Floating feed tank in unexpected condition
The vacuum preheating phase time is too long
The vacuum preheating phase time is too long
The time to reach the vacuum pressure is too long
The time to reach the thermodynamic discharge pressure
is too long
The pressure increase is lower than the set parameter
The pressure discharge time is too long
The time to reach the sterilisation pressure is too long
The pressure increase is lower than the set parameter
The chamber temperature is over the top limit for sterilisation
The chamber temperature is below the bottom limit for sterilisation
The theoretical temperature is over the top limit for sterilisation
The theoretical temperature is below the bottom limit for sterilisation
The difference between the chamber and theoretical temperature
is over the allowed limit
The final discharge time is too long
The time to reach the vacuum pressure is too long
The measured pressure is below the set parameter for the
drying phase
The time to reach the vacuum pressure is too long
The pressure balancing time is too long
The time to reach the vacuum pressure is too long in the
vacuum test
Failure to comply with the parameters in the first phase of the vacuum test
Failure to comply with the parameters in the 2nd phase of the vacuum test
Failure to comply with the temperature limits during the vacuum test
Pressure balancing failed in the vacuum test
The time to reach the test vacuum pressure threshold has been
exceeded
The time to reach the test vacuum pressure threshold has been
exceeded
Pressure delta
The safety valve has opened during test execution
The test execution time has been exceeded
The time to discharge the pressure has been exceeded
Pressure measurement less than the parameter established in the
drying phase during the test
The pressure balancing time has been exceeded during test
execution
Description
Reset
procedure
B
B
B
EN
B
B
B
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
A
71
Publicidad
